TCN75AVOA Microchip Technology, TCN75AVOA Datasheet - Page 9

• Manufacturer Part Number: TCN75AVOA
• Description: IC TEMP SENSOR SRL 2.7V 8SOIC
• Manufacturer: Microchip Technology

Specifications of TCN75AVOA

• Package / Case: 8-SOIC (3.9mm Width)
• Output Type: I²C™
• Function: Temp Monitoring System (Sensor)
• Topology: ADC (Sigma Delta), Register Bank
• Sensor Type: Internal
• Sensing Temperature: -55°C ~ 125°C
• Output Alarm: No
• Output Fan: Yes
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -55°C ~ 125°C
• Mounting Type: Surface Mount
• Temperature Threshold: Programmable
• Full Temp Accuracy: 3 C
• Digital Output - Bus Interface: 2-Wire, I2C
• Digital Output - Number Of Bits: 9 bit to 12 bit
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 55 C
• Supply Current: 500 uA
• Ic Output Type: Digital
• Sensing Accuracy Range: ± 2°C
• Temperature Sensing Range: -40°C To +125°C
• Supply Voltage Range: 2.7V To 5.5V
• Resolution (bits): 12bit
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

3.0
The descriptions of the pins are listed in
TABLE 3-1:
3.1
SDA is a bidirectional input/output pin, used to serially
transmit data to and from the host controller. This pin
requires a pull-up resistor to output data.
3.2
SCL is a clock input pin. All communication and timing
is relative to the signal on this pin. The clock is
generated by the host controller on the bus.
3.3
V
specified in the DC electrical specification table, is
applied on this pin.
3.4
GND is the system ground pin.
 2010 Microchip Technology Inc.
DD
MSOP, SOIC
is the power pin. The operating voltage, as
PIN DESCRIPTION
Serial Data Pin (SDA)
Serial Clock Pin (SCL)
Power Supply Input (V
Ground (GND)
1
2
3
4
5
6
7
8
PIN FUNCTION TABLE
Symbol
ALERT
GND
SDA
SCL
V
A2
A1
A0
DD
DD
Table
Bidirectional Serial Data
Serial Clock Input
Temperature Alert Output
Ground
Address Select Pin (bit 2)
Address Select Pin (bit 1)
Address Select Pin (bit 0)
Power Supply Input
)
3-1.
3.5
The TCN75A’s ALERT pin is an open-drain output. The
device outputs an alert signal when the ambient
temperature goes beyond the user-programmed
temperature limit.
3.6
A2, A1 and A0 are device or slave address input pins.
The address pins are the Least Significant bits (LSb) of
the device address bits. The Most Significant bits
(MSb) (A6, A5, A4, A3) are factory-set to <1001>. This
is illustrated in
TABLE 3-2:
TCN75A
Note:
Device
ALERT Output
Address Pins (A2, A1, A0)
Function
User-selectable address is shown by X.
Table
SLAVE ADDRESS
A6
1
3-2.
A5
0
A4
0
TCN75A
A3
1
DS21935D-page 9
A2
X
A1
X
A0
X