MAX6652AUB+ Maxim Integrated Products, MAX6652AUB+ Datasheet - Page 10
![IC TEMP SENS/MON 10-UMAX](/photos/6/57/65724/175-10-umax_sml.jpg)
MAX6652AUB+
Manufacturer Part Number
MAX6652AUB+
Description
IC TEMP SENS/MON 10-UMAX
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX6652AUBT.pdf
(12 pages)
Specifications of MAX6652AUB+
Function
Temp Monitoring System (Sensor)
Topology
ADC, Multiplexer, Register Bank
Sensor Type
Internal
Sensing Temperature
-40°C ~ 125°C
Output Type
I²C™/SMBus™
Output Alarm
Yes
Output Fan
No
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
10-MSOP, Micro10™, 10-uMAX, 10-uSOP
Temperature Threshold
Programmable
Full Temp Accuracy
+/- 2 C
Digital Output - Bus Interface
2-Wire, SMBus
Digital Output - Number Of Bits
8 bit
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.7 V
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Supply Current
500 uA
Ic Output Type
Digital
Sensing Accuracy Range
± 2°C
Supply Voltage Range
2.7V To 5.5V
Sensor Case Style
µMAX
No. Of Pins
10
Threshold Voltage
6V
Filter Terminals
SMD
Rohs Compliant
Yes
Temperature Sensing Range
-40°C To +125°C
Resolution (bits)
8bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Temperature Sensor and System Monitor
in a 10-Pin µMAX
Table 7. Temperature Configuration Register
Figure 1. Alert Response to Temperature Interrupts
Bit 6 is reserved.Bit 7 resets all register values to their
power-up default values. To reset all registers, set bit 7
to 1. This will also reset bit 7 to its power-up value of 0.
Temperature sensor ICs like the MAX6652 that sense
their own die temperatures must be mounted on or
close to the object whose temperature they are intend-
ed to measure. Because there is a good thermal path
between the 10-pin µMAX package’s metal leads and
the IC die, the MAX6652 can accurately measure the
temperature of the circuit board to which it is soldered.
If the sensor is intended to measure the temperature of
a heat-generating component on the circuit board, it
should be mounted as close as possible to that compo-
nent and should share supply and ground traces (if
they are not noisy) with that component where possible.
This will maximize the heat transfer from the component
to the sensor.
10
BIT
0-1
2-7
______________________________________________________________________________________
Sensing Circuit Board and Component
Hot Temperature Interrupt
Applications Information
Mode Select
Reserved
NAME
MONITORING CYCLE
TEMPERATURE
STATUS READ
INTERRUPT
ALERT
ALERT
ALERT
T
T
HYST
HOT
Temperatures
R/W
R/W
R/W
Bit 1, Bit 0
Bit 1, Bit 0
Bit 1, Bit 0
Bit 1, Bit 0
—
The thermal path between the plastic package and the
die is not as good as the path through the leads, so the
MAX6652, like all temperature sensors in plastic pack-
ages, will be less sensitive to the temperature of the
surrounding air than to the temperature of the leads.
As with any IC, the wiring and circuits must be kept
insulated and dry to avoid leakage and corrosion,
especially if the part will be operated at cold tempera-
tures where condensation can occur.
TRANSISTOR COUNT: 13,446
PROCESS: BiCMOS
00: Default Mode
01: One-Time Interrupt Mode
10: Comparator Mode
11: Default Mode
DEFAULT MODE
ONE-TIME
INTERRUPT MODE
COMPARATOR MODE
DESCRIPTION
Chip Information