MIC281-5YM6 TR Micrel Inc, MIC281-5YM6 TR Datasheet
MIC281-5YM6 TR
Specifications of MIC281-5YM6 TR
MIC281-5YM6TR
Related parts for MIC281-5YM6 TR
MIC281-5YM6 TR Summary of contents
Page 1
... General Description The MIC281 is a digital thermal sensor capable of measuring the temperature of a remote PN junction optimized for applications favoring low cost and small size. The remote junction may be an inexpensive commodity transistor, e.g., 2N3906 embedded thermal diode such as found in Intel Pentium* II/III/IV CPUs, AMD Athlon* CPUs, and Xilinx Virtex* FPGAs ...
Page 2
... Ordering Information Part Number Standard Marking Pb-FREE MIC281-0BM6* TB00 MIC281-0YM6* MIC281-1BM6* TB01 MIC281-1YM6* MIC281-2BM6* TB02 MIC281-2YM6* MIC281-3BM6* TB03 MIC281-3YM6* MIC281-4BM6 TB04 MIC281-4YM6 MIC281-5BM6* TB05 MIC281-5YM6* MIC281-6BM6* TB06 MIC281-6YM6* MIC281-7BM6* TB07 MIC281-7YM6* * Contact Micrel regarding availability Pin Configuration Pin Description Pin ...
Page 3
... Note 2 MIN A MAX Min Typ 0. 200 2.65 300 ≤ 85°C; ±1 ≤ 85°C; ±2 A 200 192 7 12 2.1 10 Max Units 0.4 mA µA µA µs 2. ±3 °C ±5 °C 240 ms 400 µA µA 0.3 V 0.5 V 0 ±1 µA MIC281 ...
Page 4
... Note 5. Guaranteed by design over the operating temperature range. Not 100% production tested. Note 6. Accuracy specifications do not include quantization noise which may ± 0.5LSB. Note 7. Devices are ESD sensitive. Observe appropriate handling precautions. Timing Diagram DATA INPUT DATA OUTPUT MIC281 Condition 3.0V ≤ V ≤ 3.6V DD 3.0V ≤ V ≤ ...
Page 5
... Meas urement E rror eakage to +3. 3. 1x10 1x10 1x10 1x10 RESISTANCE FROM T1 (Ω) E rror Due to Nois e on the C ollec tor of R emote T rans is tor 1.6 1.4 100mV P -P 1.2 1.0 0.8 0.6 50mV P -P 0.4 0.2 25mV 100 1k 10k 100k 1M 10M100M FREQUENCY (Hz) MIC281 ...
Page 6
... The SMBus Read_Byte operation is a composite write and read operation: the host first sends the device’s slave address followed by the command byte write operation. A new start bit must then be sent to the MIC281, followed by a repeat of the MIC281 Slave Address DATA ...
Page 7
... Slave Address The MIC281 will only respond to its own unique slave ad- dress. A match between the MIC281’s address and the address specified in the serial bit stream must be made to initiate communication. The MIC281’s slave address is fixed at the time of manufacture. Eight different slave addresses are available as determined by the part number ...
Page 8
... Command byte: * Any write to CONFIG will result in any A/D conversion in progress being aborted and the result discarded. The A/D will begin a new conver- sion sequence once the write operation is complete. MIC281 Remote Temperature Result (TEMP) 8-bits, read-only Remote Temperature Result Register ...
Page 9
... Die Revision Register (DIE_REV) 8-bits, read-only Die Revision Register D[5] D[4] D[3] read-only read-only MIC281 DIE REVISION NUMBER [Device revision number] 1111 1111 = D[2] D[1] read-only read-only read-only 0 1 Operation* . Read-only. Always returns 2A h D[2] D[1] ...
Page 10
... Filter Capacitor Selection It is usually desirable to employ a filter capacitor between the T1 and GND pins of the MIC281. The use of this capacitor is recommended in environments with a lot of high frequency noise (such as digital switching noise long traces or wires are used to connect to the remote diode ...
Page 11
... Layout Considerations The following guidelines should be kept in mind when design- ing and laying out circuits using the MIC281: 1. Place the MIC281 as close to the remote diode as possible, while taking care to avoid severe noise sources such as high frequency power transformers, CRTs, memory and data busses, etc ...
Page 12
... A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify MIC281 1.75 (0.069) 3 ...