MAX1617AMEE+T Maxim Integrated Products, MAX1617AMEE+T Datasheet - Page 12

• Manufacturer Part Number: MAX1617AMEE+T
• Description: IC REMOTE/LOCAL TEMP SNSR 16QSOP
• Manufacturer: Maxim Integrated Products

Specifications of MAX1617AMEE+T

• Function: Thermometer, Thermostat
• Topology: ADC, Comparator, Multiplexer, Register Bank
• Sensor Type: External & Internal
• Sensing Temperature: -55°C ~ 125°C, External Sensor
• Output Type: I²C™/SMBus™
• Output Alarm: Yes
• Output Fan: No
• Voltage - Supply: 3 V ~ 5.5 V
• Operating Temperature: -55°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 16-QSOP
• Full Temp Accuracy: +/- 3 C
• Digital Output - Bus Interface: Serial (2-Wire)
• Digital Output - Number Of Bits: 7 bit + Sign
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 55 C
• Dc: 06/08
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The Alert Response can activate several different slave
devices simultaneously, similar to the I
Call. If more than one slave attempts to respond, bus
arbitration rules apply, and the device with the lower
address code wins. The losing device does not gener-
ate an acknowledge and continues to hold the ALERT
line low until serviced (implies that the host interrupt
input is level-sensitive). Successful reading of the alert
response address clears the interrupt latch.
The 8-bit command byte register (Table 4) is the master
index that points to the various other registers within the
MAX1617A. The register’s POR state is 0000 0000, so
that a Receive Byte transmission (a protocol that lacks
the command byte) that occurs immediately after POR
returns the current local temperature data.
The one-shot command immediately forces a new conver-
sion cycle to begin. In software standby mode
(RUN/STOP bit = high), a new conversion is begun, after
which the device returns to standby mode. If a conversion
is in progress when a one-shot command is received, the
Remote/Local Temperature Sensor
with SMBus Serial Interface
Table 4. Command-Byte Bit Assignments
* If the device is in hardware standby mode at POR, both temperature registers read 0°C.
I
12
2
C is a trademark of Phillips Corp.
______________________________________________________________________________________
REGISTER
WCRW
MFGID
WLHO
WRHA
DEVID
WLLM
WRLN
RCRA
RLHN
OSHT
SPOR
RRTE
RRLS
RLTS
RRHI
WCA
RLLI
RCL
RSL
Command Byte Functions
COMMAND
0Ah
0Bh
0Ch
0Dh
FCh
00h
01h
02h
03h
04h
05h
06h
07h
08h
09h
0Eh
0Fh
FEh
FFh
2
C™ General
POR STATE
0000 0000*
0000 0000*
0000 0000
0000 0010
0111 1111
1100 1001
0111 1111
1100 1001
0100 1101
00000001
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
command is ignored. If a one-shot command is received
in auto-convert mode (RUN/STOP bit = low) between con-
versions, a new conversion begins, the conversion rate
timer is reset, and the next automatic conversion takes
place after a full delay elapses.
The configuration byte register (Table 5) is used to
mask (disable) interrupts and to put the device in soft-
ware standby mode. The lower six bits are internally set
to (XX1111), making them “don’t care” bits. Write zeros
to these bits. This register’s contents can be read back
over the serial interface.
The status byte register (Table 6) indicates which (if
any) temperature thresholds have been exceeded. This
byte also indicates whether or not the ADC is convert-
ing and whether there is an open circuit in the remote
diode DXP–DXN path. After POR, the normal state of all
the flag bits is zero, assuming none of the alarm condi-
tions are present. The status byte is cleared by any
Read local temperature: returns latest temperature
Read remote temperature: returns latest temperature
Read status byte (flags, busy signal)
Read configuration byte
Read conversion rate byte
Read local T
Read local T
Read remote T
Read remote T
Write configuration byte
Write conversion rate byte
Write local T
Write local T
Write remote T
Write remote T
One-shot command (use send-byte format)
Write software POR
Read manufacturer ID code
Read device ID code
HIGH
LOW
HIGH
LOW
HIGH
LOW
HIGH
LOW
limit
limit
Configuration Byte Functions
limit
limit
limit
limit
limit
limit
FUNCTION
Status Byte Functions