ADM1034ARQZ-R7 ON Semiconductor, ADM1034ARQZ-R7 Datasheet - Page 10

• Manufacturer Part Number: ADM1034ARQZ-R7
• Description: IC THERM/FAN SPEED CTLR 16-QSOP
• Manufacturer: ON Semiconductor

Specifications of ADM1034ARQZ-R7

• Function: Fan Control, Temp Monitor
• Topology: ADC, Comparator, Multiplexer, Register Bank
• Sensor Type: External & Internal
• Sensing Temperature: -40°C ~ 125°C, External Sensor
• Output Type: SMBus™
• Output Alarm: Yes
• Output Fan: Yes
• Voltage - Supply: 3 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 16-QSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

SMBus 2.0 Fixed and Discoverable Mode
mode, which is backwards compatible with SMBus 1.0 and
1.1. Fixed and discoverable mode supports all the same
functionality as ARP−capable mode, except for assign
address in which case it powers up with a fixed address and
is not changed by the assign address call. The fixed address
is determined by the state of the LOCATION pin on
powerup.
SMBus 2.0 Read and Write Operations
condition, defined as a high−to−low transition on the serial
data line (SDA) while the serial clock line (SCL) remains
high. This indicates that an address/data stream is to follow.
All slave peripherals connected to the serial bus respond to
the start condition and shift in the next 8 bits, which consist
of a 7−bit address (MSB first) plus an R/W bit. This last bit
determines the direction of the data transfer (whether data is
written to or read from the slave device).
Table 3. UDID Values
<127:120>
<119:112>
The ADM1034 also supports fixed and discoverable
The master initiates data transfer by establishing a start
<111:96>
<95:80>
<79:64>
<63:48>
<47:32>
Bit No.
<31:0>
1. The peripheral that corresponds to the transmitted
2. Data is sent over the serial bus in sequences of 9
address responds by pulling the data line low
during the low period before the 9th clock pulse,
which is known as the acknowledge bit. All other
devices on the bus remain idle while the selected
device waits for data to be read from or written to
it. If the R/W bit is a 0, the master writes to the
slave device. If the R/W bit is a 1, the master reads
from it.
clock pulses − 8 bits of data followed by an
acknowledge bit from the slave device. Transitions
on the data line must occur during the low period
of the clock signal and remain stable during the
high period, because a low−to−high transition
when the clock is high may be interpreted as a stop
signal. The number of data bytes that can be
Device Capabilities
Version/Revision
Vendor ID
Device ID
Interface
Subsystem Vendor ID
Subsystem Device ID
Vendor Specific ID
Name
Describes the ADM1034’s capabilities (for instance, that it supports
PEC and uses a random number address device).
UDID version number (Version 1) and silicon revision identification
Analog Devices vendor ID number, as assigned by the SBS
Implementer’s Forum or the PCI SIG.
Device ID.
Identifies the protocol layer interfaces supported by the ADM1034.
This represents SMBus 2.0 as the Interface version..
Subsystem Vendor ID = 0 (subsystem fields are unsupported).
Subsystem Device ID = 0 (subsystem fields are unsupported).
A unique number per device. Contains LOCATION information (LL)
and a 16−bit random number (x). See
setting the LLL bits.
http://onsemi.com
10
because the type of operation is determined at the beginning
and cannot be changed without starting a new operation.
data from it, the address pointer register (APR) must be set
so that the correct data register is addressed; then data can be
written into that register or read from it. The first byte of a
write operation always contains an address that is stored in
the APR. If data is to be written to the device, then the write
operation contains a second data byte, which is written to the
register selected by the APR.
the bus, followed by R/W set to 0. This is followed by two
data bytes. The first data byte is the address of the internal
data register to be written to, which is stored in the APR. The
second data byte is the data to be written to the internal data
register.
possibilities.
must be set to the correct value before data can be read from
the desired data register. To do this, perform a write to the
It is not possible to mix read and write in one operation,
To write data to one of the device data registers or to read
As illustrated in Figure 17, the device address is sent over
When reading data from a register there are two
If the ADM1034’s APR value is unknown or incorrect, it
Function
3. When all data bytes have been read or written,
transmitted over the serial bus in a single read or
write operation is limited only by what the master
and slave devices can handle.
stop conditions are established. In write mode, the
master pulls the data line high during the 10th
clock pulse to assert a stop condition. In read
mode, the master device overrides the
acknowledge bit by pulling the data line high
during the low period before the 9th clock pulse.
This is known as no acknowledge. The master
takes the data line low during the low period
before the 10th clock pulse, then high during the
10th clock pulse to assert a stop condition.
Table 5
for information on
00001010
00010001
00010000
00000000
00000100
00000000
00000000
00000000
00000000
00000000
00000LLL
11000001
11010100
00110100
xxxxxxxx
xxxxxxxx
Value