AD652JP-REEL Analog Devices Inc, AD652JP-REEL Datasheet
![IC V-F CONV SYNCH MONO 5V 20PLCC](/photos/6/52/65299/505-20-plcc_sml.jpg)
AD652JP-REEL
Specifications of AD652JP-REEL
Available stocks
Related parts for AD652JP-REEL
AD652JP-REEL Summary of contents
Page 1
FEATURES Full-scale frequency ( MHz) set by external system clock Extremely low linearity error (0.005% max at 1 MHz FS, 0.02% max at 2 MHz FS) No critical external components required Accurate 5 V reference voltage Low drift ...
Page 2
AD652 TABLE OF CONTENTS Specifications..................................................................................... 3 Absolute Maximum Ratings............................................................ 5 ESD Caution.................................................................................. 5 Definitions of Specifications ....................................................... 5 Theory of Operation ........................................................................ 6 Overrange ...................................................................................... 8 SVFC Connection for Dual Supply, Positive Input Voltages .. 9 SVFC Connections for Negative ...
Page 3
... Noninverting Input (Pin 6) Input Offset Current Input Offset Current Drift Input Offset Voltage Input Offset Voltage Drift Open-Loop Gain Common-Mode Input Range CMRR Bandwidth Output Voltage Range (Referred to Pin 6, R1 > kΩ) AD652JP/AQ/SQ Min Typ Max Min ±0.5 ±1 ±0.5 ±1 ±0.5 ±1.5 ± ...
Page 4
... Rated Voltage Operating Range Dual Supply Single Supply (− Quiescent Current Digital Common Analog Common TEMPERATURE RANGE Specified Performance JP, KP Grade AQ, BQ Grade SQ Grade 1 Referred to internal PLCC package, tested input range only. REF AD652JP/AQ/SQ Min Typ Max Min 0.5 5 − − 4 − ...
Page 5
ABSOLUTE MAXIMUM RATINGS Table 2. Parameter Total Supply Voltage +V to − Maximum Input Voltage (Figure 6) Maximum Output Current (Open Collector Output) Amplifier Short-Circuit to Ground Storage Temperature Range: CERDIP Storage Temperature Range: PLCC ESD CAUTION ESD ...
Page 6
AD652 THEORY OF OPERATION A synchronous VFC is similar to other voltage-to-frequency converters in that an integrator is used to perform a charge- balance of the input signal with an internal reference current. However, rather than using a one-shot as ...
Page 7
Figure 4 shows that the period between output pulses is constrained exact multiple of the clock period. Consider an input current of exactly one quarter the value of the reference current. In order ...
Page 8
AD652 Another way to view this is that the output is a frequency of approximately one-quarter of the clock that has been phase modulated. A constant frequency can be thought of as accumulating phase linearly with time at a rate ...
Page 9
SVFC CONNECTION FOR DUAL SUPPLY, POSITIVE INPUT VOLTAGES Figure 8 shows the AD652 connection scheme for the traditional dual supply, positive input mode of operation. The ±V range is from ± ±18 V. When + shown ...
Page 10
AD652 20kΩ C INT V IN ±5V SVFC CONNECTION FOR BIPOLAR INPUT VOLTAGES A bipolar input voltage of ±5 V can be accommodated by injecting a 250 µA current into Pin 5 (see Figure 10). A −5 V signal provides ...
Page 11
– – NC PLCC CONNECTIONS The PLCC packaged AD652 offers additional input resistors not found on the CERDIP-packaged device. These resistors provide the user with additional input voltage ranges. Besides the 10 V range ...
Page 12
AD652 This gain trim should be done with an input voltage and the output frequency should be adjusted to exactly 45% of the clock frequency. Since the device settles into a divide-by-2 mode for an input overrange ...
Page 13
The one-shot capacitor controls the pulse width of the frequency output. The pulse is initiated by the rising edge of the clock signal. The delay time between the rising edge of the clock and the falling edge of the frequency ...
Page 14
AD652 SINGLE-SUPPLY OPERATION In addition to the Digital Ground being connected to –V also possible to connect Analog Ground to –V Thus, the device is truly operating from a single-supply voltage that can range from ...
Page 15
FREQUENCY-TO-VOLTAGE CONVERTER The AD652 SVFC also works as a frequency-to-voltage converter. Figure 22 shows the connection diagram for F/V conversion. In this case, the negative input of the comparator is fed the input pulses. Either comparator input may be used ...
Page 16
AD652 DECOUPLING AND GROUNDING It is good engineering practice to use bypass capacitors on the supply-voltage pins, and to insert small valued resistors (10 Ω to 100 Ω) in the supply lines to provide a measure of decoupling between the ...
Page 17
V1 0V–10V – V2 0V–10V + V OUT FREQUENCY OUTPUT MULTIPLIER The AD652 can serve as a frequency output multiplier when used in conjunction with a standard voltage-to-frequency converter. Figure 23 shows the low cost AD654 VFC being used ...
Page 18
AD652 This can be shown in equation form, where f output frequency and f is the AD652 output frequency: OUT 1 MHz ⎛ ⎞ f ⎜ ⎟ C ⎜ ⎟ ...
Page 19
AD652 4 SYNCHRONOUS 0.02µF VOLTAGE-TO- 5 FREQUENCY CONVERTER IN2 8 15pF –V S TIM 9904A TANK 1 2 TANK 2 XTAL 2 3 GND 1 XTAL 4 7.4µH 4 ...
Page 20
AD652 SVFC Demultiplexer The demultiplexer needed to separate the combined signals is shown in Figure 30. A phase-locked loop drives another 4-phase clock chip to lock onto the reconstructed clock signal. The sync pulses are distinguished from the data pulses ...
Page 21
S 1 VOLTS 2 OUT AD652 4 SYNCHRONOUS 0.02µF VOLTAGE-TO- 5 FREQUENCY CONVERTER –V S +5V 1.5kΩ DRIVER 1 2 10kΩ 1.2kΩ 3 6.8kΩ AD589 1.2V –15V 7915 REG –15V LO ...
Page 22
AD652 ISOLATED FRONT END In some applications, it may be necessary to have complete galvanic isolation between the analog signals being measured and the digital portions of the circuit. The circuit shown in Figure 32 runs off a single 5 ...
Page 23
DELTA MODULATOR The circuit of Figure 34 shows the AD652 configured as a delta modulator. A reference voltage is applied to the input of the integrator (Pin 7), which sets the steady state output frequency at one-half of the AD652 ...
Page 24
AD652 BRIDGE TRANSDUCER INTERFACE The circuit of Figure 38 illustrates a simple interface between the AD652 and a bridge-type transducer. The AD652 is an ideal choice because its buffered 5 V reference can be used as the bridge excitation, thereby ...
Page 25
OUTLINE DIMENSIONS 0.200 (5.08) 0.200 (5.08) 0.125 (3.18) 0.048 (1.21) 0.042 (1.07) 0.048 (1.21) 0.042 (1.07) 0.020 (0.50) R 0.358 (9.09) 0.342 (8.69) 0.005 0.098 (2.49) 0.310 (7.87) (0.13) MAX MIN 0.220 (5.59 PIN 0.060 ...
Page 26
... AD652 ORDERING GUIDE Model Gain Drift, 100 kHz AD652JP 50 ppm/°C max AD652JP-REEL 50 ppm/°C max AD652JP-REEL7 50 ppm/°C max AD652KP 25 ppm/°C max AD652KP-REEL 25 ppm/°C max 2 50 ppm/°C max AD652AQ 2 AD652BQ 25 ppm/°C max 2 AD652SE/883B 50 ppm/°C max ...
Page 27
NOTES Rev Page AD652 ...
Page 28
AD652 NOTES © 2004 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C00798–0–5/04(C) Rev Page ...