AD652AQ Analog Devices Inc, AD652AQ Datasheet - Page 5

• Manufacturer Part Number: AD652AQ
• Description: IV V-F CONVERTER SYNC 16-CDIP
• Manufacturer: Analog Devices Inc
• Type: Voltage to Frequencyr

Specifications of AD652AQ

• Rohs Status: RoHS non-compliant
• Frequency - Max: 2MHz
• Full Scale: ±50ppm/°C
• Linearity: ±0.02%
• Mounting Type: Through Hole
• Package / Case: 16-CDIP (0.300", 7.62mm)
• Full Scale Range: 1MHz To 2MHz
• Linearity %: 0.02%
• Supply Voltage Range: ± 6V To ± 18V
• Digital Ic Case Style: DIP
• No. Of Pins: 16
• Frequency Max: 2MHz
• Termination Type: Through Hole
• Converter Function: VFC
• Full Scale Frequency: 2000
• Power Supply Requirement: Single/Dual
• Single Supply Voltage (max): 36V
• Single Supply Voltage (min): 12V
• Dual Supply Voltage (typ): ±15V
• Dual Supply Voltage (min): ±6V
• Dual Supply Voltage (max): ±18V
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Package Type: CDIP
• Converter Type: Voltage to Frequency
• Current, Quiescent Supply: ±11 mA (Typ.)
• Frequency Range: 5 MHz (Typ.)
• Input Impedance: 20 Kiloohms
• Number Of Pins: 20
• Temperature, Operating, Maximum: 85 °C
• Temperature, Operating, Minimum: -40 °C
• Voltage, Range: ±6 to ±18 V
• Voltage, Supply: 36 V
• Filter Terminals: Through Hole
• Rohs Compliant: No
• Calibration Error Fs Typ: 5%
• Lead Free Status / Rohs Status: Not Compliant

ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
Total Supply Voltage +V
Maximum Input Voltage (Figure 6)
Maximum Output Current
Amplifier Short-Circuit to Ground
Storage Temperature Range: CERDIP
Storage Temperature Range: PLCC
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
DEFINITIONS OF SPECIFICATIONS
Gain Error
The gain of a voltage-to-frequency converter is the scale factor
setting that provides the nominal conversion relationship, e.g.,
1 MHz full scale. The gain error is the difference in slope
between the actual and ideal transfer functions for the V-F
converter.
Linearity Error
The linearity error of a V-F is the deviation of the actual
transfer function from a straight line passing through the
endpoints of the transfer function.
Gain Temperature Coefficient
The gain temperature coefficient is the rate of change in full-
scale frequency as a function of the temperature from +25°C to
T
MIN
(Open Collector Output)
or T
MAX
.
S
to −V
S
Ratings
36 V
36 V
50 mA
Indefinite
−65°C to +150°C
−65°C to +150°C
Rev. C | Page 5 of 28
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Table 3. Pin Configurations
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Q-16 Package
+V
TRIM
TRIM
OP AMP OUT
OP AMP “−“
OP AMP “+”
10 VOLT INPUT
−V
C
CLOCK INPUT
FREQ OUT
DIGITAL GND
ANALOG GND
COMP “−“
COMP “+”
COMP REF
OS
S
S
P-20A Package
NC
+V
NC
OP AMP OUT
OP AMP “−“
OP AMP “+”
5 VOLT INPUT
10 VOLT INPUT
8 VOLT INPUT
OPTIONAL 10 V INPUT
−V
C
CLOCK INPUT
FREQ OUT
DIGITAL GND
ANALOG GND
COMP “−“
COMP “+”
NC
COMP REF
OS
S
S
AD652