LT3570IUF#TRPBF Linear Technology, LT3570IUF#TRPBF Datasheet - Page 14

• Manufacturer Part Number: LT3570IUF#TRPBF
• Description: IC PWM BUCK BST DIV CM 24QFN
• Manufacturer: Linear Technology

Specifications of LT3570IUF#TRPBF

• Topology: Step-Down (Buck) (1), Step-Up (Boost) (1), Linear (LDO) (1)
• Function: Automotive
• Number Of Outputs: 3
• Frequency - Switching: 500kHz ~ 2.1MHz
• Voltage/current - Output 1: Adj to 0.8V, 1.5A
• Voltage/current - Output 2: Adj to 0.8V, 1.5A
• Voltage/current - Output 3: Controller
• W/led Driver: No
• W/supervisor: No
• W/sequencer: No
• Voltage - Supply: 2.5 V ~ 36 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: *
• Package / Case: 24-QFN
• Frequency-max: 2.75MHz
• Duty Cycle: 95%
• Pwm Type: Current Mode
• Buck: Yes
• Boost: Yes
• Flyback: No
• Inverting: No
• Doubler: No
• Divider: Yes
• Cuk: No
• Isolated: No
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

LT3570
APPLICATIONS INFORMATION
Boost Diode Selection
A Schottky diode is recommended for use with the LT3570
inverter/boost regulator. The Microsemi UPS120 is a very
good choice. Where the input to output voltage differen-
tial exceeds 20V, use the UPS140 (a 40V diode). These
diodes are rated to handle an average forward current of
1A. For applications where the average forward current
of the diode is less than 0.5A, use an ON Semiconductor
MBR0520L diode.
BOOST Pin Considerations
The capacitor and diode tied to the BOOST pin generate
a voltage that is higher than the input voltage. In most
cases, a 0.1μF capacitor and fast switching diode (such
as the CMDSH-3 or MMSD914LT1) will work well. Fig-
ure 2 shows three ways to arrange the boost circuit. The
BOOST pin must be more than 2.5V above the SW pin for
full effi ciency. For outputs of 3.3V and higher, the standard
circuit (Figure 2a) is best. For outputs between 2.8V and
3.3V, use a small Schottky diode (such as the BAT-54).
For lower output voltages, the boost diode can be tied
to the input (Figure 2b). The circuit in Figure 2a is more
effi cient because the BOOST pin current comes from a
lower voltage source. Finally, as shown in Figure 2c, the
anode of the boost diode can be tied to another source
that is at least 3V. For example, if you are generating 3.3V
and 1.8V and the 3.3V is on whenever the 1.8V is on, the
1.8V boost diode can be connected to the 3.3V output. In
any case, be sure that the maximum voltage at the BOOST
pin is less than 60V and the voltage difference between
the BOOST and SW2 pins is less than 25V.
The minimum operating voltage of an LT3570 application
is limited by the undervoltage lockout (2.5V) and by the
maximum duty cycle. The boost circuit also limits the
minimum input voltage for proper start-up. If the input
voltage ramps slowly, or the LT3570 turns on when the
output is already in regulation, the boost capacitor may
not be fully charged. Because the boost capacitor charges
with the energy stored in the inductor, the circuit will rely
on some minimum load current to get the boost circuit
running properly. This minimum load will depend on input
and output voltages, and on the arrangement of the boost
circuit. The minimum load current generally goes to zero
14
once the circuit has started. Even without an output load
current, in many cases the discharged output capacitor will
present a load to the switcher that will allow it to start.
Switcher Frequency Compensation
The LT3570 uses current mode control to regulate the
output. This simplifi es loop compensation. In particular, the
LT3570 does not depend on the ESR of the output capaci-
tor for stability so you are free to use ceramic capacitors
to achieve low output ripple and small circuit size.
To compensate the feedback loop of the LT3570, a series
resistor-capacitor network should be connected from
the V
the range of 500pF to 4.7nF will suffi ce. A good starting
value for the compensation capacitor, C
C
pin to GND. For most applications, a capacitor in
V
EXT
Figure 2. Boost Pin Confi gurations
V
V
V
D3
D3
IN
IN
IN
BOOST
LT3570
BOOST
LT3570
BOOST
LT3570
GND
GND
GND
SW
SW
SW
(2a)
(2b)
(2c)
C3
C5
C5
D2
D2
D2
D3
C
3570 F02
, is 1nF . The
C2
C2
C2
3570fb