C1632C103K5RACTU Kemet, C1632C103K5RACTU Datasheet - Page 11
![CAP 4-ARRAY 10000PF 50V X7R 1632](/photos/39/81/398104/4408317_sml.jpg)
C1632C103K5RACTU
Manufacturer Part Number
C1632C103K5RACTU
Description
CAP 4-ARRAY 10000PF 50V X7R 1632
Manufacturer
Kemet
Type
Ceramicr
Specifications of C1632C103K5RACTU
Capacitance
10000pF
Voltage - Rated
50V
Dielectric Material
Ceramic
Number Of Capacitors
4
Circuit Type
Isolated
Temperature Coefficient
X7R
Tolerance
±10%
Mounting Type
Surface Mount
Package / Case
0612 (1632 Metric)
Height
0.053" (1.35mm)
Size / Dimension
0.126" L x 0.063" W (3.20mm x 1.60mm)
No. Of Capacitors
4
Tolerance (+ Or -)
10%
Voltage
50VDC
Number Of Terminals
8Terminal
Temp Coeff (dielectric)
X7R
Operating Temp Range
-55C to 125C
Mounting Style
Surface Mount
Construction
SMT Chip
Failure Rate
Not Required
Product Height (mm)
1.35mm
Product Depth (mm)
1.6mm
Product Length (mm)
3.2mm
Lead Diameter (nom)
Not Requiredmm
Terminal Pitch
0.8mm
Capacitance Tolerance
± 10%
Voltage Rating
50V
Capacitor Case Style
0612
Operating Temperature Range
-55°C To +125°C
Capacitor Mounting
SMD
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
C1632C103K5RAC
C1632C103K5RAC7800
C1632C103K5RAC7800
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3VDC–250VDC (Commercial Grade)
Figure 1 – Embossed (Plastic) Carrier Tape Dimensions
Table 6 – Embossed (Plastic) Carrier Tape Dimensions
Metric will govern
1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and
2. The tape with or without components shall pass around R without damage (see Figure 5).
3. If S
4. B1 dimension is a reference dimension for tape feeder clearance only.
5. The cavity defi ned by A
Tape Size
Tape Size
B
hole location shall be applied independent of each other.
(a) the component does not protrude above the top surface of the carrier tape.
(b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
(c) rotation of the component is limited to 20° maximum for 8 and 12mm tapes and 10° maximum for 16mm tapes (see Figure 3).
(d) lateral movement of the component is restricted to 0.5 mm maximum for 8mm and 12mm wide tape and to 1.0mm maximum for 16mm tape (see Figure 4).
(e) for KPS Series product A
(f) see Addendum in EIA Document 481 for standards relating to more precise taping requirements.
12mm
16mm
12mm
16mm
1
8mm
8mm
S
1
<1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Document 481 paragraph 4.3 (b)).
1
B
including draft concentric about B
1
is for tape feeder reference only,
T
T
Ko
T
(0.059 +0.004/-0.0)
Cover Tape
2
1
Single (4mm) &
Double (8mm)
1.5 +0.10/-0.0
Triple (12mm)
Single (4mm)
Pitch
D
0
0
, B
Center Lines of Cavity
0
and K
0
and B
o
.
0
shall surround the component with suffi cient clearance that:
0
are measured on a plane 0.3mm above the bottom of the pocket.
B
D
(0.039)
(0.059)
(0.323)
(0.476)
Note 1
Note 4
(0.171)
ØDo
1
4.35
1
12.1
8.2
1.0
1.5
User Direction of Unreeling
Max.
Min.
P
Constant Dimensions — Millimeters (Inches)
Variable Dimensions — Millimeters (Inches)
2
(0.069 ± 0.004)
1.75 ± 0.10
Po
P
1
E
(0.246)
(0.404)
(0.561)
10.25
14.25
6.25
2
E
Min.
1
tolerance on tape ±0.2 mm]
[10 pitches cumulative
Ao
ØD
1
(0.157 ± 0.004)
(0.138 ± 0.002)
(0.217 ± 0.002)
(0.217 ± 0.002)
Bo
3.5 ± 0.05
5.5 ± 0.05
5.5 ± 0.05
4.0 ± 0.10
see Note 1 Table 5
Embossment
For cavity size,
P
F
0
F
E
2
E
1
W
(0.079 ± 0.002)
(0.157 ± 0.004)
(0.315 ± 0.004)
(0.315 ± 0.004)
2.0 ± 0.05
4.0 ± 0.10
8.0 ± 0.10
8.0 ± 0.10
P
P
2
1
(0.984)
T
(0.098)
(0.181)
Note 2
(1.181)
(0.181)
R Ref.
25.0
2
2.5
4.6
4.6
30
Max
S
W Max
(0.327)
(0.484)
(0.642)
(0.024)
Note 3
0.600
C1002_X7R • 6/15/2011
12.3
16.3
1
8.3
Min.
T Max.
(0.024)
0.600
A
0
Note 5
,B
0
& K
T
(0.004)
0.100
1
Max.
0
11