DS1050U-001 Maxim Integrated Products, DS1050U-001 Datasheet
DS1050U-001
Specifications of DS1050U-001
Available stocks
Related parts for DS1050U-001
DS1050U-001 Summary of contents
Page 1
... SOIC DS1050Z-005 5kHz 8-Pin 150-mil SOIC DS1050Z-010 10kHz 8-Pin 150-mil SOIC DS1050Z-025 25kHz 8-Pin 150 mil SOIC 8-Pin 118-mil mSOP DS1050U-001 1kHz 8-Pin 118-mil mSOP DS1050U-005 5kHz 8-Pin 118-mil mSOP DS1050U-010 10kHz DS1050U-025 25kHz 8-Pin 118-mil µSOP DESCRIPTION The DS1050 is a programmable, 5-bit, pulse-width modulator featuring a 2-wire addressable controlled interface ...
Page 2
OPERATION Interface protocol is simplified to an 8-bit control byte and 8-bit data byte. Information can be read or written to the DS1050 including a commanded shutdown operation. Power-Up Configuration The DS1050 powers-up to half-scale (10000B) providing 50% duty-cycle. In ...
Page 3
The following bus protocol has been defined (see Figure 2). § Data transfer may be initiated only when the bus is not busy. § During data transfer, the data line must remain stable whenever the clock line is HIGH. Changes ...
Page 4
The master device generates all serial clock pulses and the START and STOP conditions. A transfer is ended with a STOP condition or with a repeated START condition. Since a repeated START condition is also the beginning of the next ...
Page 5
The command operation “Set Shutdown Mode” is used to provide a low-current (inactive state) state for the DS1050. When in a low-current state the DS1050 will draw currents less than or equal to 1mA. The PWM output will be high ...
Page 6
STOP condition. The 2-wire serial timing diagram is presented in Figure ...
Page 7
ABSOLUTE MAXIMUM RATINGS* Voltage on Any Pin Relative to Ground Operating Temperature Storage Temperature Soldering Temperature * This is a stress rating only and functional operation of the device at these or any other conditions above those conditions indicated in ...
Page 8
AC ELECTRICAL CHARACTERISTICS PARAMETER SYMBOL SCL Clock f SCL Frequency Bus Free Time t BUF Between STOP and START Condition Hold Time t HD:STA (Repeated) START Condition Low Period of SCL t LOW Clock High Period of SCL t HIGH ...
Page 9
NOTES: 1. All voltages are referenced to ground specified with outputs open I/O pins of fast mode devices must not obstruct the SDA and SCL lines Address Inputs, A0, A1, and A2, should ...
Page 10
BLOCK DIAGRAM Figure 1 OSCILLATOR CONTROL LOGIC SCL SDA Serial Port 2-WIRE ADDRESSABLE SERIAL PORT OVERVIEW Figure 2 SDA m sb slave address SCL 1 2 Start C ondition COMMAND/CONTROL BYTE Figure 3 msb 0 Device Identifier ...
Page 11
DS1050 COMMANDS AND PROTOCOL Figure 4 SET PWM DUTY CYCLE (a) (b) SET SHUT-DOWN MODE (c) RECALL MODE (d) READ PWM DUTY CYCLE (e) CONTROL BYTE MSB LSB ...
Page 12
SERIAL DIAGRAMS Figure 5 SDA t BUF t LOW SCL t HD:STA STOP START HIGH t SU:STA t t HD:STA SU:DAT REPEATED START HD:STA t SU:STO ...
Page 13
TYPICAL OPERATING CHARACTERISTICS DS1050 (V = 5.0V +25ºC, unless otherwise specified 100 DS1050 SUPPLY ...
Page 14
TYPICAL OPERATING CHARACTERISTICS DS1050-001 (V = 5.0V +25ºC, unless otherwise specified S1050-001 vs 1.030 1.025 1.020 1.015 1.010 ...
Page 15
TYPICAL OPERATING CHARACTERISTICS DS1050-005 (V = 5.0V +25ºC, unless otherwise specified) CC DS1050-005 FREQUENCY vs. TEMPERATURE 5.2 5.15 5.1 5.05 5 4.95 -40 -20 DS1050-005 SUPPLY CURRENT vs. TEMPERATURE -40 ...
Page 16
TYPICAL OPERATING CHARACTERISTICS DS1050-010 ( +25ºC, unless otherwise specified) CC DS1050-010 FREQUENCY vs. TEMPERATURE 10.7 10.65 10.6 10.55 10.5 10.45 10.4 10.35 10.3 -40 -20 DS1050-010 SUPPLY CURRENT vs. TEMPERATURE ...
Page 17
TYPICAL OPERATING CHARACTERISTICS DS1050-025 (V = 5.0V +25ºC, unless otherwise specified) CC DS1050-025 FREQUENCY vs. TEMPERATURE 26.8 26.6 26.4 26.2 26 25.8 25.6 25.4 25.2 -40 -20 DS1050-025 SUPPLY CURRENT vs. TEMPERATURE ...