IRU3037CF International Rectifier, IRU3037CF Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/3/338/international_rectifier_sml.jpg)
IRU3037CF
Manufacturer Part Number
IRU3037CF
Description
IC CNTRLR PWM SYNC 200KHZ 8TSSOP
Manufacturer
International Rectifier
Datasheet
1.IRU3037CSTRPBF.pdf
(21 pages)
Specifications of IRU3037CF
Pwm Type
Voltage Mode
Number Of Outputs
1
Frequency - Max
220kHz
Duty Cycle
95%
Voltage - Supply
5 V ~ 12 V
Buck
Yes
Boost
No
Flyback
No
Inverting
No
Doubler
No
Divider
No
Cuk
No
Isolated
No
Operating Temperature
0°C ~ 70°C
Package / Case
8-TSSOP
Frequency-max
220kHz
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
*IRU3037CF
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
IRU3037CFTRPBF
Manufacturer:
IR
Quantity:
3 000
Part Number:
IRU3037CFTRPBF
Manufacturer:
IR
Quantity:
20 000
APPLICATION INFORMATION
Design Example:
The following example is a typical application for IRU3037,
the schematic is Figure 18 on page 14.
Output Voltage Programming
Output voltage is programmed by reference voltage and
external voltage divider. The Fb pin is the inverting input
of the error amplifier, which is internally referenced to
1.25V (0.8V for IRU3037A). The divider is ratioed to pro-
vide 1.25V at the Fb pin when the output is at its desired
value. The output voltage is defined by using the follow-
ing equation:
When an external resistor divider is connected to the
output as shown in Figure 3.
Equation (1) can be rewritten as:
If the high value feedback resistors are used, the input
bias current of the Fb pin could cause a slight increase
in output voltage. The output voltage set point can be
more accurate by using precision resistor.
Figure 3 - Typical application of the IRU3037 for
V
V
I
∆V
f
V
R
Choose R
This will result to R
OUT
S
IN
OUT
OUT
6
= 200KHz
OUT
= R
= 5V
= 4A
= 3.3V
= V
= 100mV
5
programming the output voltage.
×
REF
5
IRU3037
(
= 1KΩ
×
V
V
OUT
REF
(
1 +
6
- 1
Fb
= 1.65KΩ
R
R
)
6
5
)
V
---(1)
OUT
R
R
6
5
www.irf.com
Soft-Start Programming
The soft-start timing can be programmed by selecting
the soft start capacitance value. The start up time of the
converter can be calculated by using:
For a start-up time of 7.5ms, the soft-start capacitor will
be 0.1µF. Choose a ceramic capacitor at 0.1µF.
Shutdown
The converter can be shutdown by pulling the soft-start
pin below 0.5V. The control MOSFET turns off and the
synchronous MOSFET turns on during shutdown.
Boost Supply Vc
To drive the high-side switch it is necessary to supply a
gate voltage at least 4V greater than the bus voltage.
This is achieved by using a charge pump configuration
as shown in Figure 18. The capacitor is charged up to
approximately twice the bus voltage. A capacitor in the
range of 0.1µF to 1µF is generally adequate for most
applications. In application, when a separate voltage
source is available the boost circuit can be avoided as
shown in Figure 1.
Input Capacitor Selection
The input filter capacitor should be based on how much
ripple the supply can tolerate on the DC input line. The
larger capacitor, the less ripple expected but consider
should be taken for the higher surge current during the
power-up. The IRU3037 provides the soft-start function
which controls and limits the current surge. The value of
the input capacitor can be calculated by the following
formula:
IRU3037/IRU3037A & (PbF)
t
Where:
C
C
Where:
C
I
∆t is the turn on time of the high-side switch (µs)
∆V is the allowable peak to peak voltage ripple (V)
START
IN
SS
IN
IN
is the input current (A)
=
is the input capacitance (µF)
is the soft-start capacitor (µF)
= 75×Css (ms)
I
IN
∆V
× ∆t
---(3)
---(2)
5