UC2845BD1 ON Semiconductor, UC2845BD1 Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
UC2845BD1
Manufacturer Part Number
UC2845BD1
Description
IC CTRLR CURRENT MODE HP 8-SOIC
Manufacturer
ON Semiconductor
Datasheet
1.UC3844BDR2G.pdf
(19 pages)
Specifications of UC2845BD1
Pwm Type
Current Mode
Number Of Outputs
1
Frequency - Max
275kHz
Duty Cycle
50%
Voltage - Supply
8.2 V ~ 25 V
Buck
No
Boost
Yes
Flyback
Yes
Inverting
Yes
Doubler
No
Divider
No
Cuk
No
Isolated
Yes
Operating Temperature
-25°C ~ 85°C
Package / Case
8-SOIC (3.9mm Width)
Frequency-max
275kHz
Duty Cycle (max)
48 %
Output Voltage
4.95 V to 5.05 V
Output Current
1000 mA
Mounting Style
SMD/SMT
Switching Frequency
500 KHz
Operating Supply Voltage
30 V
Maximum Operating Temperature
+ 85 C
Fall Time
50 ns
Minimum Operating Temperature
- 25 C
Rise Time
50 ns
Synchronous Pin
No
Topology
Boost, Flyback
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
UC2845BD1013TR
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
UC2845BD1R2
Manufacturer:
ON
Quantity:
2 392
Company:
Part Number:
UC2845BD1R2G
Manufacturer:
ON
Quantity:
30 000
Company:
Part Number:
UC2845BD1R2G
Manufacturer:
ON Semiconductor
Quantity:
20 000
Part Number:
UC2845BD1R2G
Manufacturer:
ON/安森美
Quantity:
20 000
fixed frequency, current mode controllers. They are
specifically designed for Off−Line and DC−DC converter
applications offering the designer a cost−effective solution
with minimal external components. A representative block
diagram is shown in Figure 16.
Oscillator
selected for the timing components R
is charged from the 5.0 V reference through resistor R
approximately 2.8 V and discharged to 1.2 V by an internal
current sink. During the discharge of C
generates an internal blanking pulse that holds the center
input of the NOR gate high. This causes the Output to be in
a low state, thus producing a controlled amount of output
deadtime. An internal flip−flop has been incorporated in the
UCX844/5B which blanks the output off every other clock
cycle by holding one of the inputs of the NOR gate high. This
in combination with the C
deadtimes programmable from 50% to 70%. Figure 2 shows
R
Deadtime versus Frequency, both for given values of C
Note that many values of R
oscillator frequency but only one combination will yield a
specific output deadtime at a given frequency. The oscillator
thresholds are temperature compensated to within ±6%
at 50 kHz. Also, because of industry trends moving the
UC384X into higher and higher frequency applications, the
UC384XB is guaranteed to within ±10% at 250 kHz.
to frequency−lock the converter to an external system clock.
This can be accomplished by applying a clock signal to the
circuit shown in Figure 18. For reliable locking, the
free−running oscillator frequency should be set about 10%
less than the clock frequency. A method for multi−unit
synchronization is shown in Figure 19. By tailoring the
clock waveform, accurate Output duty cycle clamping can
be achieved to realize output deadtimes of greater than 70%.
Error Amplifier
inverting input and output is provided. It features a typical
dc voltage gain of 90 dB, and a unity gain bandwidth of
1.0 MHz with 57 degrees of phase margin (Figure 6). The
non−inverting input is internally biased at 2.5 V and is not
pinned out. The converter output voltage is typically divided
down and monitored by the inverting input. The maximum
input bias current is −2.0 mA which can cause an output
voltage error that is equal to the product of the input bias
current and the equivalent input divider source resistance.
loop compensation (Figure 29). The output voltage is offset
by two diode drops (≈1.4 V) and divided by three before it
connects to the inverting input of the Current Sense
T
The UC3844B, UC3845B series are high performance,
The oscillator frequency is programmed by the values
In many noise−sensitive applications it may be desirable
A fully compensated Error Amplifier with access to the
The Error Amp Output (Pin 1) is provided for external
versus Oscillator Frequency and Figure 3, Output
T
discharge period yields output
T
and C
T
T
and C
will give the same
T
, the oscillator
T
. Capacitor C
OPERATING DESCRIPTION
http://onsemi.com
T
to
T
T
.
7
Comparator. This guarantees that no drive pulses appear at
the Output (Pin 6) when Pin 1 is at its lowest state (V
This occurs when the power supply is operating and the load
is removed, or at the beginning of a soft−start interval
(Figures 21, 22). The Error Amp minimum feedback
resistance is limited by the amplifier’s source current
(0.5 mA) and the required output voltage (V
comparator’s 1.0 V clamp level:
Current Sense Comparator and PWM Latch
controller, whereby output switch conduction is initiated by
the oscillator and terminated when the peak inductor current
reaches the threshold level established by the Error
Amplifier Output/Compensation (Pin 1). Thus the error
signal controls the peak inductor current on a
cycle−by−cycle basis. The Current Sense Comparator PWM
Latch configuration used ensures that only a single pulse
appears at the Output during any given oscillator cycle. The
inductor current is converted to a voltage by inserting the
ground−referenced sense resistor R
source of output switch Q1. This voltage is monitored by the
Current Sense Input (Pin 3) and compared to a level derived
from the Error Amp Output. The peak inductor current under
normal operating conditions is controlled by the voltage at
Pin 1 where:
supply output is overloaded or if output voltage sensing is
lost. Under these conditions, the Current Sense Comparator
threshold will be internally clamped to 1.0 V. Therefore the
maximum peak switch current is:
becomes desirable to reduce the internal clamp voltage in order
to keep the power dissipation of R
simple method to adjust this voltage is shown in Figure 20. The
two external diodes are used to compensate the internal diodes,
yielding a constant clamp voltage over temperature. Erratic
operation due to noise pickup can result if there is an excessive
reduction of the I
waveform can usually be observed and may cause the power
supply to exhibit an instability when the output is lightly
loaded. This spike is due to the power transformer
interwinding capacitance and output rectifier recovery time.
The addition of an RC filter on the Current Sense Input with
a time constant that approximates the spike duration will
usually eliminate the instability (refer to Figure 24).
The UC3844B, UC3845B operate as a current mode
Abnormal operating conditions occur when the power
When designing a high power switching regulator it
A narrow spike on the leading edge of the current
R
f(min)
≈
pk(max)
I
pk
3.0 (1.0 V) + 1.4 V
I
pk(max)
=
clamp voltage.
0.5 mA
V
(Pin 1)
=
3 R
− 1.4 V
1.0 V
S
R
S
S
to a reasonable level. A
S
= 8800 W
in series with the
OH
) to reach the
OL
).