MAX8632ETI+T Maxim Integrated Products, MAX8632ETI+T Datasheet - Page 17
![IC PWR SUPPLY DDR 28-TQFN](/photos/6/61/66150/28-tqfn_21-0139h_sml.jpg)
MAX8632ETI+T
Manufacturer Part Number
MAX8632ETI+T
Description
IC PWR SUPPLY DDR 28-TQFN
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX8632ETIT.pdf
(29 pages)
Specifications of MAX8632ETI+T
Applications
Controller, DDR
Voltage - Input
2 ~ 28 V
Number Of Outputs
1
Voltage - Output
1.8V, 2.5V, 0.7 ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
28-TQFN Exposed Pad
Output Voltage
1.8 V, 2.5 V, 0.7 V to 5.5 V
Output Current
15 A
Input Voltage
2 V to 28 V
Mounting Style
SMD/SMT
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
When the output voltage rises above 116% of the nomi-
nal regulation voltage and OVP is enabled (OVP/UVP =
AV
shuts down the PWM controller, and immediately pulls
DH low and forces DL high. This turns on the synchro-
nous-rectifier MOSFET (Q2 in Figure 8) with a 100%
duty cycle, rapidly discharging the output capacitor
and clamping the output to ground. Once the output
reaches 0.1V, DL is switched off, preventing the possi-
bility of a negative voltage on the output. Toggle SHDN
or cycle AV
restart the controller. OVP is disabled when OVP/UVP is
connected to REF or GND (see Table 3). OVP only
applies to the buck output. The VTT and VTTR outputs
do not have overvoltage protection.
When the output voltage drops below 70% of its regula-
tion voltage while UVP is enabled, the controller sets
the fault latch and begins the discharge mode (see the
SHDN and Output Discharge section). UVP is ignored
for at least 10ms (min) after startup or after a rising
edge on SHDN. Toggle SHDN or cycle AV
below 1V to clear the fault latch and restart the con-
troller. UVP is disabled when OVP/UVP is left open or
connected to GND (see Table 3). UVP only applies to
the buck output. The VTT and VTTR outputs do not
have undervoltage protection.
The MAX8632 features two thermal-fault-protection cir-
cuits. One monitors the buck-regulator portion of the IC
and the other monitors the linear regulator (VTT) and
the reference buffer output (VTTR). When the junction
Table 3. OVP/UVP Fault Protection
DD
OVP/UVP
OPEN
AV
GND
REF
or open), the OVP circuit sets the fault latch,
DD
DD
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
below 1V to clear the fault latch and
DL forced low when SHDN is low.
DL forced low when SHDN is low.
Output is discharged through an
Output is discharged through an
______________________________________________________________________________________
internal 10Ω resistance.
internal 10Ω resistance.
Undervoltage Protection (UVP)
Thermal Fault Protection
Overvoltage Protection (OVP)
DISCHARGE
Yes.
Yes.
No.
No.
DD
power
UVP PROTECTION
temperature of the buck-regulator portion of the
MAX8632 rises above +160°C, a thermal sensor acti-
vates the fault latch, pulls POK1 low, and shuts down
the buck-controller output using discharge mode
regardless of the OVP/UVP setting. Toggle SHDN or
cycle AV
the junction temperature cools by 15°C. If the VTT and
VTTR regulator portion of the IC has its die temperature
rise above +160°C, then VTT and VTTR shut off, go
high impedance, and restart after the die portion of the
IC cools by 15°C. Both thermal faults are independent.
For example, if the VTT output is overloaded to the
point that it triggers its thermal fault, the buck regulator
continues to function.
Firmly establish the input voltage range (V
mum load current (I
choosing a switching frequency and inductor operating
point (ripple current ratio or LIR). The primary design
trade-off lies in choosing a good switching frequency
and inductor operating point, and the following four fac-
tors dictate the rest of the design:
• Input Voltage Range. The maximum value (V
• Maximum Load Current. There are two values to con-
Disabled
Disabled
Enabled
Enabled
must accommodate the worst-case voltage. The mini-
mum value (V
voltage after drops due to connectors and fuses. If
there is a choice, lower input voltages result in better
efficiency.
sider. The peak load current (I
instantaneous component stresses and filtering
requirements and thus drives output capacitor selec-
tion, inductor saturation rating, and the design of the
DD
below 1V to reactivate the controller after
IN(MIN)
LOAD
) must account for the lowest
) in the buck regulator before
Design Procedure
OVP PROTECTION
PEAK
Disabled
Disabled
Enabled
Enabled
) determines the
IN
) and maxi-
IN(MAX)
17
)