MAX1567ETL+T Maxim Integrated Products, MAX1567ETL+T Datasheet - Page 8
![IC DGTL CAM PWR-SUP 6CH 40TQFN](/photos/6/65/66502/40-qfn_pkg_sml.jpg)
MAX1567ETL+T
Manufacturer Part Number
MAX1567ETL+T
Description
IC DGTL CAM PWR-SUP 6CH 40TQFN
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX1567ETLT.pdf
(35 pages)
Specifications of MAX1567ETL+T
Applications
Controller, Digital Camera
Voltage - Input
0.7 ~ 5.5 V
Number Of Outputs
7
Voltage - Output
1.25 ~ 5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
40-TQFN Exposed Pad
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Six-Channel, High-Efficiency, Digital
Camera Power Supplies
ELECTRICAL CHARACTERISTICS (continued)
(V
Note 2: The MAX1566/MAX1567 are powered from the step-up output (PVSU). An internal low-voltage startup oscillator drives the
Note 3: Since the device is powered from PVSU, a Schottky rectifier, connected from the battery to PVSU, is required for low-voltage
Note 4: The step-up regulator is in startup mode until this voltage is reached. Do not apply full load current during startup. A power-
Note 5: The step-up current limit in startup refers to the LXSU switch current limit, not the output current limit.
Note 6: If the main converter is configured as a step-up (SUSD = PVSU), the P-channel synchronous rectifier is disabled until the
Note 7: Operation in dropout (100% duty cycle) can only be maintained for 100,000 OSC cycles before the output is considered
Note 8: ONM, ONSD, ON1, ON2, and ON3 are disabled until 1024 OSC cycles after PVSU reaches 2.7V.
8
AUX3 FBL or FBH to CC
Transconductance
FB_ Input Leakage Current
DL_ Driver Resistance
AUX1OK Output Low
AUX1OK Leakage Current
OVERLOAD PROTECTION
SCF Leakage Current
SCF Output Low Voltage
LOGIC INPUTS (ON_, SUSD)
ONSU Input Low Level
ONSU Input High Level
ONM, ONSD, ON1, ON2, ON3,
SUSD Input Low Level
ONM, ONSD, ON1, ON2, ON3,
SUSD Input High Level
SUSD Input Leakage
PVSU
_______________________________________________________________________________________
= V
step-up starting at approximately 0.9V until PVSU reaches approximately 2.5V. When PVSU reaches 2.5V, the main control
circuitry takes over. Once the step-up is up and running, it can maintain operation with very low input voltages; however,
output current is limited.
startup.
OK output can be used with an external PFET to gate the load until the step-up is in regulation. See the
and SCF Connections section.
2.5V normal operation threshold has been exceeded. If the main converter is configured as a step-down (SUSD = GND), all
step-down operation is locked out until the normal operation threshold has been exceeded. When the main is configured as
a step-down, operation in dropout (100% duty cycle) can only be maintained for 100,000 OSC cycles before the output is
considered faulted, triggering global shutdown.
faulted, triggering global shutdown.
PARAMETER
PV
= V
PVM
= V
PVSD
= V
INDL2
Output high or low
0.1mA into AUX1OK
ONSU = GND
ONSU = PVSU, FBSU = 1.5V
0.1mA into SCF
1.1V < PVSU < 1.8V
1.8V ≤ PVSU < 2.5V
2.5V ≤ PVSU < 5.5V
1.1V < PVSU < 1.8V
1.8V < PVSU < 5.5V
2.7V < PVSU < 5.5V (Note 8)
2.7V < PVSU < 5.5V (Note 8)
= 3.6V, T
A
= -40°C to +85°C, unless otherwise noted.)
CONDITIONS
(PVSU
- 0.2)
-100
MIN
1.6
1.6
35
AUX1OK , SDOK ,
+100
MAX
150
0.1
0.1
0.2
0.4
0.5
0.5
7
1
1
1
UNITS
µS
nA
µA
µA
µA
Ω
V
V
V
V
V
V