LTC1174CS8-5#PBF Linear Technology, LTC1174CS8-5#PBF Datasheet - Page 10
![IC DC/DC CONV STP-DWN&INVRT8SOIC](/photos/7/58/75833/ltc1174cs8-5_pbf_sml.jpg)
LTC1174CS8-5#PBF
Manufacturer Part Number
LTC1174CS8-5#PBF
Description
IC DC/DC CONV STP-DWN&INVRT8SOIC
Manufacturer
Linear Technology
Type
Step-Down (Buck), Invertingr
Datasheet
1.LTC1174CN8PBF.pdf
(20 pages)
Specifications of LTC1174CS8-5#PBF
Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
5V
Current - Output
1A
Frequency - Switching
200kHz
Voltage - Input
4 ~ 18.5 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
APPLICATIO S I FOR ATIO
LTC1174
LTC1174-3.3/LTC1174-5
output voltage is now taken off the GND pin. Therefore,
the maximum input voltage is now determined by the
difference between the absolute maximum voltage rating
and the output voltage. A maximum of 12V is specified in
Figure 5, giving the circuit a 1.5V of headroom for V
that the circuit can operate from a minimum of 4V, making
it ideal for a 4 NiCad cell application. For a higher output
current circuit, please refer to the Typical Applications
section.
Absolute Maximum Ratings and Latchup Prevention
The absolute maximum ratings specify that SW (Pin 5) can
never exceed V
situation should never occur. It could, however, if the
output is held up while the supply is pulled down. A con-
dition where this could potentially occur is when a battery
is supplying power to an LTC1174/LTC1174-3.3/
10
**
**
*
*
ADJUSTABLE APPLICATIONS
LOW NOISE APPLICATIONS
3
2
7
AVX TPSD476K016
COILTRONICS CTX50-4
Figure 4. LTC1174 Adjustable Configuration
Figure 5. Positive-to-Negative 5V Converter
LB
I
LB
PGM
INPUT VOLTAGE
IN
OUT
LTC1174HV-5
LTC1174
4V TO 12V
IN
GND
V
SHUTDOWN
IN
(Pin 6) by more than 0.3V. Normally this
6
4
U
V
V
OUT
SW
FB
1
1
8
5
U
MBRS140T3
50µH**
6.8nF**
100pF*
0.1µF
W
+
+
1174 F04
47µF*
16V
×2
47µF*
16V
×2
R2
R1
U
V
V
–5V
45mA
OUT
1174 F05
OUT
IN
. Note
LTC1174-5 regulator and also to one or more loads in
parallel with the the regulator’s V
connected while the LTC1174/LTC1174-3.3/LTC1174-5
regulator is supplying a light load and one of the parallel
circuits is a heavy load, the input capacitor of the LTC1174/
LTC1174-3.3/LTC1174-5 regulator could be pulled down
faster than the output capacitor, causing the absolute
maximum ratings to be exceeded. The result is often a
latchup which can be destructive if V
tery disconnect is possible as a result of mechanical stress,
bad battery contacts or use of a lithium-ion battery with
a built-in internal disconnect. The user needs to assess
his/her application to determine whether this situation
could occur. If so, additional protection is necessary.
Prevention against latchup can be accomplished by sim-
ply connecting a Schottky diode across the SW and V
pins as shown in Figure 6. The diode will normally be
reverse biased unless V
time the diode will clamp the (V
than the 0.6V required for latchup. Note that a low leakage
Schottky should be used to minimize the effect on no-load
supply current. Schottky diodes such as MBR0530, BAS85
and BAT84 work well. Another more serious effect of the
protection diode leakage is that at no load with nothing to
provide a sink for this leakage current, the output voltage
can potentially float above the maximum allowable toler-
ance. To prevent this from occuring, a resistor must be
connected between V
enough to sink the maximum possible leakage current.
Figure 6. Preventing Absolute Maximum
Ratings from Being Exceeded
V
LTC1174-3.3
IN
LTC1174-5
LTC1174
OUT
SW
IN
is pulled below V
and ground with a value low
LATCHUP
PROTECTION
SCHOTTKY
OUT
IN
– V
. If the battery is dis-
IN
+
IN
is reapplied. Bat-
) potential to less
1174 F06
V
OUT
OUT
at which
1174fe
IN