IR3843WMTR1PBF International Rectifier, IR3843WMTR1PBF Datasheet - Page 17

• Manufacturer Part Number: IR3843WMTR1PBF
• Description: IC REG SYNC BUCK 2A 15-QFN
• Manufacturer: International Rectifier
• Series: SupIRBuck™r
• Type: Step-Down (Buck)r

Specifications of IR3843WMTR1PBF

• Internal Switch(s): Yes
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 0.7 ~ 14.4 V
• Current - Output: 2A
• Frequency - Switching: 225kHz ~ 1.65MHz
• Voltage - Input: 1.5 ~ 16 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 15-PowerVQFN
• Power - Output: 394mW
• Primary Input Voltage: 16V
• No. Of Outputs: 1
• Output Voltage: 14.4V
• Output Current: 2A
• No. Of Pins: 15
• Operating Temperature Range: -40°C To +125°C
• Output Voltage Adjustable Max, Vout: 14.4V
• Rohs Compliant: Yes
• Part Status: Preferred
• Package: PQFN / 5 x 6
• Circuit: Single Output
• Iout (a): 2
• Switch Freq (khz): 250 - 1500
• Input Range (v): 1.5 - 16
• Output Range (v): 0.7 - 0.9*Vin
• Ocp Otp Uvlo Pre-bias Soft Start And: PGOOD + EN + SEQ + OVD
• Design Tool: Yes
• Server Storage: Yes
• Routers Switches: Yes
• Base Station Telecom: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: IR3843WMTR1PBFTR

Minimum on time Considerations
The minimum ON time is the shortest amount of
time for which the Control FET may be reliably
turned on, and this depends on the internal
timing delays. For the IR3843W, the typical
minimum on-time is specified as 100 ns.
Any design or application using the IR3843W
must ensure operation with a pulse width that is
higher than this minimum on-time and preferably
higher than 150 ns. This is necessary for the
circuit to operate without jitter and pulse-
skipping, which can cause high inductor current
ripple and high output voltage ripple.
In any application that uses the IR3843W, the
following condition must be satisfied:
The minimum output voltage is limited by the
reference voltage and hence V
Therefore, for V
Therefore, at the maximum recommended input
voltage 16V and minimum output voltage, the
converter should be designed at a switching
frequency that does not exceed 290 kHz.
However, practical considerations dictate that
any application that demands a pulse width
smaller than 175ns may not exhibit jitter free
operation over the entire load range. This means
that for 16 V input voltage, the operation
frequency should be limited to 250 kHz.
Rev 10.0
∴
∴
V
in
V
∴
∴
t
in
×
on
V
t
on
F
×
t
(min)
in
on
s
(min)
F
×
out(min)
s
=
≤
=
F
≤
≤
V
s
V
F
D
≤
t
in
t
out
150
s
V
on
≤
0.7
on
V
out
×
(min)
= 0.7 V,
(min)
t
in
V
on
V
F
ns
V
out
×
out
(min)
s
F
=
s
4
.
67
out(min)
×
10
6
V/s
= 0.7 V.
Maximum Duty Ratio Considerations
A fixed off-time of 200 ns maximum is specified
for the IR3843W. This provides an upper limit on
the operating duty ratio at any given switching
frequency. It is clear that, higher the switching
frequency, the lower is the maximum duty ratio at
which the IR3843W can operate. To allow a
margin of 50ns, the maximum operating duty
ratio in any application using the IR3843W
should still accommodate about 250 ns off-time.
Fig 10. shows a plot of the maximum duty ratio
v/s the switching frequency, with 250 ns off-time.
95
90
85
80
75
70
65
60
55
Fig. 10. Maximum duty cycle v/s switching
250
450
frequency.
650
S w itching Frequency (kH z )
M a x Duty Cycle
IR3843WMPbF
850
1050
1250
PD-97507
1450
17
1650