MCP1640-I/MC Microchip Technology, MCP1640-I/MC Datasheet - Page 15
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
MCP1640-I/MC
Manufacturer Part Number
MCP1640-I/MC
Description
IC CONV DC-DC STEPUP SYNC 8DFN
Manufacturer
Microchip Technology
Type
Step-Up (Boost)r
Specifications of MCP1640-I/MC
Package / Case
8-DFN
Internal Switch(s)
Yes
Synchronous Rectifier
Yes
Number Of Outputs
1
Voltage - Output
2 ~ 5.5 V
Current - Output
100mA
Frequency - Switching
500kHz
Voltage - Input
0.8 ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Mounting Style
SMD/SMT
Duty Cycle (max)
90 %
Efficiency
96 %
Input / Supply Voltage (max)
0.8 V
Input / Supply Voltage (min)
0.65 V
Load Regulation
0.01 %
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Operating Temperature Range
- 40 C to + 85 C
Output Current
350 mA
Output Voltage
5 V
Switching Frequency
500 KHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MCP1640-I/MC
Manufacturer:
MICROCHIP
Quantity:
12 000
Installation and Operation
Periodically, the microcontroller will come out from Sleep mode for a short period of
time to search if its power supply (V
), which comes from MCP1640 V
pin,
DD
OUT
reaches 2.3V threshold. This is accomplished by the internal analog comparator of the
microcontroller.
This compares a fraction of V
(from R4) with the 0.6V internal voltage reference.
OUT
To avoid losing power on the passive components and reduce the complexity of the
schematic, the application also uses MCP1640’s feedback network (R2-R3-R4) as the
input to the PIC comparator.
The PIC12F617 microcontroller works down to 2.0V V
. If a 2.3V threshold is
DD
detected, the GP2 pin of the microcontroller will set the EN pin of the MCP1640 high
for a short time, to pump up the output capacitor to a 3.3V regulated voltage. After
that, EN is pulled down again and MCP1640 enters into the True Output Disconnect
Shutdown option. V
is sustained by the output capacitor (C2) for approximately 2
OUT
seconds until it reaches the 2.3V threshold.
Generally, the EN drive signal frequency depends on the MCP1640’s output capacitor
value and PIC12F617’s sleep current. The typical time to charge the output capacitor
to 3.3V is 750 ns, with a load less than 10 µA.
The EN signal is inverted using the transistor Q1 to ensure the start of the application
when a battery is inserted.
By pressing the button S1, the GP1 microcontroller port switches the P-MOS
transistor ON (Q2), powering the load. The load is supplied for a fixed period of time
(approximately 25 seconds), unless the button is pressed.
The PIC12F617 measures the battery voltage when the switch load (Q2) is ON. If the
battery voltage is lower than 0.8V, the LED (D1) will flash. Battery voltage is measured
using the R7-C4 filter and the A/D channel present on pin 3 (GP4) of the
microcontroller.
2.2.3
Programming the PIC12F617 Microcontroller
For board evaluation, Microchip provides a firmware package, downloadable from
Microchip’s web site. The board is factory programmed for an active 10 seconds output,
after the button S1 is pressed. The green LED on the board flashes when a low battery
condition (less than 0.8V input) is detected, but the board will operate at the lowest
input voltage possible. All parameters may be changed in firmware to the desired value,
according to the output/input capability. The source code is rich in comments and helps
the user to define the board.
HI-TECH C compiler is used to compile the source code and create the hex files for
downloading to the reference board. The HI-TECH compiler is available for download
on Microchip’s web site. The compiler is not included with the evaluation board kit.
Header J3 can be used for in-system circuit programming. J3 is not populated on the
board. A five pin header connector may be soldered in J3’s place. A PICkit™3
programmer may be connected to J3 to program the evaluation board.
© 2010 Microchip Technology Inc.
DS51922A-page 15