LM2575T-12/NOPB National Semiconductor, LM2575T-12/NOPB Datasheet - Page 8
![IC REG SIMPLE SWITCHER TO-220-5](/photos/7/60/76069/pkg_t05a_drawing__14_sml.jpg)
LM2575T-12/NOPB
Manufacturer Part Number
LM2575T-12/NOPB
Description
IC REG SIMPLE SWITCHER TO-220-5
Manufacturer
National Semiconductor
Series
SIMPLE SWITCHER®r
Type
Step-Down (Buck)r
Datasheet
1.LM2575S-5.0NOPB.pdf
(28 pages)
Specifications of LM2575T-12/NOPB
Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
12V
Current - Output
1A
Frequency - Switching
52kHz
Voltage - Input
4 ~ 40 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Through Hole
Package / Case
TO-220-5 (Straight Leads)
Primary Input Voltage
25V
No. Of Outputs
1
Output Voltage
5V
Output Current
1A
No. Of Pins
5
Operating Temperature Range
-40°C To +125°C
Msl
MSL 1 - Unlimited
Filter Terminals
Through Hole
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
Lead Free Status / Rohs Status
RoHS Compliant part
Electrostatic Device
Other names
*LM2575T-12
*LM2575T-12/NOPB
LM2575T-12
*LM2575T-12/NOPB
LM2575T-12
www.national.com
θ
θ
θ
θ
θ
θ
ON /OFF CONTROL Test Circuit Figure 2
V
V
I
I
IH
IL
Symbol
JA
JA
JC
JA
JA
JA
IH
IL
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics.
Note 2: All limits guaranteed at room temperature (standard type face) and at temperature extremes (bold type face). All limits are used to calculate Average
Outgoing Quality Level, and all are 100% production tested.
Note 3: All limits guaranteed at room temperature (standard type face) and at temperature extremes (bold type face). All room temperature limits are 100%
production tested. All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC) methods.
Note 4: External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance. When the LM1575/
LM2575 is used as shown in the Figure 2 test circuit, system performance will be as shown in system parameters section of Electrical Characteristics.
Note 5: Output (pin 2) sourcing current. No diode, inductor or capacitor connected to output pin.
Note 6: Feedback (pin 4) removed from output and connected to 0V.
Note 7: Feedback (pin 4) removed from output and connected to +12V for the Adjustable, 3.3V, and 5V versions, and +25V for the 12V and 15V versions, to
force the output transistor OFF.
Note 8: V
Note 9: Junction to ambient thermal resistance (no external heat sink) for the 5 lead TO-220 package mounted vertically, with ½ inch leads in a socket, or on a
PC board with minimum copper area.
Note 10: Junction to ambient thermal resistance (no external heat sink) for the 5 lead TO-220 package mounted vertically, with ½ inch leads soldered to a PC
board containing approximately 4 square inches of copper area surrounding the leads.
Note 11: Junction to ambient thermal resistance with approximately 1 square inch of pc board copper surrounding the leads. Additional copper area will lower
thermal resistance further. See thermal model in Switchers made Simple software.
Note 12: If the TO-263 package is used, the thermal resistance can be reduced by increasing the PC board copper area thermally connected to the package:
Using 0.5 square inches of copper area, θ
θ
Note 13: The oscillator frequency reduces to approximately 18 kHz in the event of an output short or an overload which causes the regulated output voltage to
drop approximately 40% from the nominal output voltage. This self protection feature lowers the average power dissipation of the IC by lowering the minimum
duty cycle from 5% down to approximately 2%.
Note 14: Refer to RETS LM1575J for current revision of military RETS/SMD.
JA
is 32°C/W.
IN
Thermal Resistance
ON /OFF Pin Logic
Input Level
ON /OFF Pin Input
Current
= 40V (60V for the high voltage version).
Parameter
JA
T Package, Junction to Ambient (Note 9)
T Package, Junction to Ambient (Note 10)
T Package, Junction to Case
N Package, Junction to Ambient (Note 11)
M Package, Junction to Ambient (Note 11)
S Package, Junction to Ambient (Note 12)
V
V
ON /OFF Pin = 5V (OFF)
ON /OFF Pin = 0V (ON)
is 50°C/W; with 1 square inch of copper area, θ
OUT
OUT
= 0V
= Nominal Output Voltage
Conditions
8
JA
is 37°C/W; and with 1.6 or more square inches of copper area,
Typ
100
1.4
1.2
65
45
85
37
12
2
0
LM1575-XX
(Note 2)
2.2/2.4
1.0/0.8
Limit
30
10
LM2575HV-XX
LM2575-XX
(Note 3)
2.2/2.4
1.0/0.8
Limit
30
10
μA(Max)
μA(Max)
(Limits)
V(Max)
V(Min)
Units
°C/W
μA
μA