LM26001QMXA/NOPB National Semiconductor, LM26001QMXA/NOPB Datasheet - Page 9
![IC REG SW 1.5A W/SLEEP 16-TSSOP](/photos/7/36/73657/pkg_mxa16a_sml.jpg)
LM26001QMXA/NOPB
Manufacturer Part Number
LM26001QMXA/NOPB
Description
IC REG SW 1.5A W/SLEEP 16-TSSOP
Manufacturer
National Semiconductor
Series
PowerWise®r
Type
Step-Down (Buck)r
Datasheet
1.LM26001QMXANOPB.pdf
(18 pages)
Specifications of LM26001QMXA/NOPB
Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
1.25 ~ 35 V
Current - Output
1.5A
Frequency - Switching
150kHz ~ 500kHz
Voltage - Input
4 ~ 38 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
16-TSSOP Exposed Pad, 16-eTSSOP, 16-HTSSOP
Power - Output
2.6W
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
*LM26001QMXA/NOPB
LM26001QMXA
LM26001QMXA
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM26001QMXA/NOPB
Manufacturer:
TI/NSC
Quantity:
19 400
Operation Description
GENERAL
The LM26001 is a current mode PWM buck regulator. At the
beginning of each clock cycle, the internal high-side switch
turns on, allowing current to ramp up in the inductor. The in-
ductor current is internally monitored during each switching
cycle. A control signal derived from the inductor current is
compared to the voltage control signal at the COMP pin, de-
rived from the feedback voltage. When the inductor current
reaches the threshold, the high-side switch is turned off and
inductor current ramps down. While the switch is off, inductor
current is supplied through the catch diode. This cycle repeats
at the next clock cycle. In this way, duty cycle and output volt-
age are controlled by regulating inductor current. Current
mode control provides superior line and load regulation. Other
benefits include cycle by cycle current limiting and a simplified
compensation scheme. Typical PWM waveforms are shown
in Figure 1.
SLEEP MODE
In light load conditions, the LM26001 automatically switches
into sleep mode for improved efficiency. As loading decreas-
es, the voltage at FB increases and the COMP voltage de-
creases. When the COMP voltage reaches the 0.6V (typical)
clamp threshold, and the FB voltage rises 1% above nominal,
sleep mode is enabled and switching stops. The regulator re-
mains in sleep mode until the FB voltage falls to the reset
threshold, at which point switching resumes. This 1% FB win-
dow limits the corresponding output ripple to approximately
1% of nominal output voltage. The sleep cycle will repeat until
load current is increased. Figure 2 shows typical switching
and output voltage waveforms in sleep mode.
FIGURE 1. PWM Waveforms
1A Load, Vin = 12V
20179419
9
In sleep mode, quiescent current is reduced to less than 40
µA when not switching. The DC sleep mode threshold can be
calculated according to the equation below:
Where Imin = Ilim/16 (2.5A/16 typically) and D = duty cycle,
defined as (Vout + Vdiode)/Vin.
When load current increases above this limit, the LM26001 is
forced back into normal PWM operation. The sleep mode
threshold varies with frequency, inductance, and duty cycle
as shown in Figure 3.
Below the sleep threshold, decreasing load current results in
longer sleep cycles, which can be quantified as shown below:
Where Dwake is the percentage of time awake when the load
current is below the sleep threshold.
Sleep mode combined with low IQ operation minimizes the
input supply current. Input supply current in sleep mode can
be calculated based on the wake duty cycle, as shown below:
FIGURE 3. Sleep Mode Threshold vs Vin
FIGURE 2. Sleep Mode Waveforms
25mA Load, Vin = 12V
Dwake = Iload/Isleep
Vout = 3.3V
20179420
20179422
www.national.com