LT1576CS8-SYNC#TRPBF Linear Technology, LT1576CS8-SYNC#TRPBF Datasheet - Page 23
![IC SW REG STEP-DOWN 200KHZ 8SOIC](/photos/7/57/75766/lt1576cs8_sml.jpg)
LT1576CS8-SYNC#TRPBF
Manufacturer Part Number
LT1576CS8-SYNC#TRPBF
Description
IC SW REG STEP-DOWN 200KHZ 8SOIC
Manufacturer
Linear Technology
Type
Step-Down (Buck)r
Datasheet
1.LT1576CS8PBF.pdf
(28 pages)
Specifications of LT1576CS8-SYNC#TRPBF
Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
Adj to 1.2V
Current - Output
1.5A
Frequency - Switching
200kHz
Voltage - Input
5 ~ 25 V
Operating Temperature
0°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LT1576CS8-SYNC#TRPBFLT1576CS8-SYNC#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
APPLICATIONS
The output of the regulator contains both the desired low
frequency transient information and a reasonable amount
of high frequency (200kHz) ripple. The ripple makes it
difficult to observe the small transient, so a two-pole,
100kHz filter has been added. This filter is not particularly
critical; even if it attenuated the transient signal slightly,
this wouldn’t matter because amplitude is not critical.
After verifying that the setup is working correctly, I start
varying load current and input voltage to see if I can find
any combination that makes the transient response look
suspiciously “ringy.” This procedure may lead to an ad-
justment for best loop stability or faster loop transient
response. Nearly always you will find that loop response
looks better if you add in several k for R
if necessary, because as explained before, R
may require the addition of C
If everything looks OK, I use a heat gun and cold spray on
the circuit (especially the output capacitor) to bring out
any temperature-dependent characteristics.
Keep in mind that this procedure does not take initial
component tolerance into account. You should see fairly
clean response under all load and line conditions to ensure
that component variations will not cause problems. One
note here: according to Murphy, the component most
likely to be changed in production is the output capacitor,
because that is the component most likely to have manu-
facturer variations (in ESR) large enough to cause prob-
lems. It would be a wise move to lock down the sources of
the output capacitor in production.
A possible exception to the “clean response” rule is at very
light loads, as evidenced in Figure 14 with I
Switching regulators tend to have dramatic shifts in loop
response at very light loads, mostly because the inductor
current becomes discontinuous. One common result is very
slow but stable characteristics. A second possibility is low
phase margin, as evidenced by ringing at the output with
transients. The good news is that the low phase margin at
light loads is not particularly sensitive to component varia-
tion, so if it looks reasonable under a transient test, it will
U
INFORMATION
U
F
to control V
W
C
LOAD
. Do this only
C
C
pin ripple.
U
above 1k
= 50mA.
5.5V TO
probably not be a problem in production. Note that fre-
quency of the light load ringing may vary with component
tolerance but phase margin generally hangs in there.
POSITIVE-TO-NEGATIVE CONVERTER
The circuit in Figure 15 is a classic positive-to-negative
topology using a grounded inductor. It differs from the
standard approach in the way the IC chip derives its
feedback signal, however, because the LT1576 accepts
only positive feedback signals, the ground pin must be tied
to the regulated negative output. A resistor divider to
ground or, in this case, the sense pin, then provides the
proper feedback voltage for the chip.
** MAXIMUM LOAD CURRENT DEPENDS ON MINIMUM INPUT VOLTAGE
Inverting regulators differ from buck regulators in the
basic switching network. Current is delivered to the output
as square waves with a peak-to-peak amplitude much
greater than load current. This means that maximum load
current will be significantly less than the LT1576’s 1.5A
maximum switch current, even with large inductor values.
The buck converter in comparison, delivers current to the
output as a triangular wave superimposed on a DC level
equal to load current, and load current can approach 1.5A
* INCREASE L1 TO 30 H OR 60 H FOR HIGHER CURRENT APPLICATIONS.
INPUT
10 F TO
SEE APPLICATIONS INFORMATION
AND INDUCTOR SIZE. SEE APPLICATIONS INFORMATION
20V
50 F
C3
+
Figure 15. Positive-to-Negative Converter
V
IN
GND
BOOST
LT576
V
C
R
V
C
C
SW
FB
C
LT1576/LT1576-5
D2
1N5818
C2
0.33 F
4.99k
R2
1N4148
15 H
15.8k
L1*
D1
R1
+
C1
100 F
10V TANT
2
23
OUTPUT**
– 5V, 0.5A
1576 F15