LTC3703EGN-5#TR Linear Technology, LTC3703EGN-5#TR Datasheet - Page 19
![no-image](/images/manufacturer_photos/0/3/388/linear_technology_sml.jpg)
LTC3703EGN-5#TR
Manufacturer Part Number
LTC3703EGN-5#TR
Description
IC BUCK/BOOST SYNC ADJ 5A 16SSOP
Manufacturer
Linear Technology
Type
Step-Down (Buck), Step-Up (Boost)r
Datasheet
1.LTC3703EGN-5PBF.pdf
(32 pages)
Specifications of LTC3703EGN-5#TR
Internal Switch(s)
No
Synchronous Rectifier
Yes
Number Of Outputs
1
Voltage - Output
0.8 ~ 55.8 V
Current - Output
5A
Frequency - Switching
100kHz ~ 600kHz
Voltage - Input
9.3 ~ 60 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
16-SSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Power - Output
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
APPLICATIO S I FOR ATIO
Figure 12 shows an improved “Type 2” circuit that uses an
additional pole-zero pair to temporarily remove 90° of
phase shift. This allows the loop to remain stable with 90°
more phase shift in the LC section, provided the loop
reaches 0dB gain near the center of the phase “bump.”
Type 2 loops work well in systems where the ESR zero in
the LC roll-off happens close to the LC pole, limiting the
total phase shift due to the LC. The additional phase
compensation in the feedback amplifier allows the 0dB
point to be at or above the LC pole frequency, improving
loop bandwidth substantially over a simple Type 1 loop. It
has limited ability to compensate for LC combinations
where low capacitor ESR keeps the phase shift near 180°
feedback amplifier, on the other hand, gives us a handle
with which to adjust the AC response. The goal is to have
180° phase shift at DC (so the loop regulates) and some-
thing less than 360° phase shift at the point that the loop
gain falls to 0dB. The simplest strategy is to set up the
feedback amplifier as an inverting integrator, with the 0dB
frequency lower than the LC pole (Figure 11). This “Type
1” configuration is stable but transient response is less
than exceptional if the LC pole is at a low frequency.
IN
R1
R
V
B
REF
FB
Figure 11. Type 1 Schematic and Transfer Function
Figure 10. Transfer Function of Buck Modulator
–
+
A
C1
V
0
PHASE
GAIN
U
OUT
0
U
–12dB/OCT
PHASE
–6dB/OCT
GAIN
W
–6dB/OCT
37035 F10
FREQ
–90
–180
–270
–360
U
37035 F11
FREQ
–90
–180
–270
–360
for an extended frequency range. LTC3703-5 circuits
using conventional switching grade electrolytic output
capacitors can often get acceptable phase margin with
Type 2 compensation.
“Type 3” loops (Figure 13) use two poles and two zeros to
obtain a 180° phase boost in the middle of the frequency
band. A properly designed Type 3 circuit can maintain
acceptable loop stability even when low output capacitor
ESR causes the LC section to approach 180° phase shift
well above the initial LC roll-off. As with a Type 2 circuit,
the loop should cross through 0dB in the middle of the
phase bump to maximize phase margin. Many LTC3703-5
circuits using low ESR tantalum or OS-CON output capaci-
tors need Type 3 compensation to obtain acceptable phase
margin with a high bandwidth feedback loop.
Feedback Component Selection
Selecting the R and C values for a typical Type 2 or Type 3
loop is a nontrivial task. The applications shown in this
data sheet show typical values, optimized for the power
components shown. They should give acceptable perfor-
mance with similar power components, but can be way off
IN
IN
R1
R
B
R1
R
V
B
REF
FB
Figure 12. Type 2 Schematic and Transfer Function
R3
V
Figure 13. Type 3 Schematic and Transfer Function
REF
FB
C3
–
+
R2
–
+
R2
C2
C2
C1
C1
OUT
OUT
0
0
PHASE
GAIN
GAIN
–6dB/OCT
–6dB/OCT
LTC3703-5
+6dB/OCT
PHASE
–6dB/OCT
–6dB/OCT
19
37035 F12
37035fa
FREQ
–90
–180
–270
–360
37035 F13
FREQ
–90
–180
–270
–360