LTC1871IMS-7#TRPBF Linear Technology, LTC1871IMS-7#TRPBF Datasheet - Page 16
![IC CONTRLR CURRENT MODE 10-MSOP](/photos/1/36/13608/10-msop_05-08-1661_sml.jpg)
LTC1871IMS-7#TRPBF
Manufacturer Part Number
LTC1871IMS-7#TRPBF
Description
IC CONTRLR CURRENT MODE 10-MSOP
Manufacturer
Linear Technology
Type
Step-Up (Boost), Flyback, Sepicr
Datasheet
1.LTC1871EMS-7.pdf
(32 pages)
Specifications of LTC1871IMS-7#TRPBF
Internal Switch(s)
No
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
1.23 ~ 36 V
Current - Output
50mA
Frequency - Switching
50kHz ~ 1MHz
Voltage - Input
6 ~ 36 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
10-MSOP, Micro10™, 10-uMAX, 10-uSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
LTC1871-7
APPLICATIONS INFORMATION
From a known power dissipated in the power MOSFET, its
junction temperature can be obtained using the following
formula:
The R
the R
the case to the ambient temperature (R
of T
used in the iterative calculation process.
Boost Converter: Output Diode Selection
To maximize effi ciency, a fast switching diode with low
forward drop and low reverse leakage is desired. The output
diode in a boost converter conducts current during the
switch off-time. The peak reverse voltage that the diode
must withstand is equal to the regulator output voltage.
The average forward current in normal operation is equal
to the output current, and the peak current is equal to the
peak inductor current.
The power dissipated by the diode is:
and the diode junction temperature is:
16
T
P
T
I
D(PEAK)
J
J
J
D
TH(JC)
can then be compared to the original, assumed value
= T
= T
TH(JA)
= I
Figure 12. Normalized R
A
A
O(MAX)
+ P
+ P
for the device plus the thermal resistance from
=I
to be used in this equation normally includes
2.0
1.0
0.5
1.5
0
FET
L(PEAK)
D
–50
• R
• V
• R
TH(JA)
D
JUNCTION TEMPERATURE (°C)
TH(JA)
= 1+
0
2
50
DS(ON)
•
1– D
I
O(MAX)
vs Temperature
100
MAX
TH(CA)
18717 F12
150
). This value
The R
the R
the board to the ambient temperature in the enclosure.
Remember to keep the diode lead lengths short and to
observe proper switch-node layout (see Board Layout
Checklist) to avoid excessive ringing and increased dis-
sipation.
Boost Converter: Output Capacitor Selection
Contributions of ESR (equivalent series resistance), ESL
(equivalent series inductance) and the bulk capacitance
must be considered when choosing the correct component
for a given output ripple voltage. The effects of these three
parameters (ESR, ESL and bulk C) on the output voltage
ripple waveform are illustrated in Figure 13 for a typical
boost converter.
The choice of component(s) begins with the maximum
acceptable ripple voltage (expressed as a percentage of
the output voltage), and how this ripple should be divided
between the ESR step and the charging/discharging ΔV.
For the purpose of simplicity we will choose 2% for the
maximum output ripple, to be divided equally between the
ESR step and the charging/discharging ΔV. This percentage
ripple will change, depending on the requirements of the
application, and the equations provided below can easily
be modifi ed.
For a 1% contribution to the total ripple voltage, the ESR
of the output capacitor can be determined using the fol-
lowing equation:
where:
For the bulk C component, which also contributes 1% to
the total ripple:
ESR
I
C
IN(PEAK)
OUT
TH(JC)
TH(JA)
COUT
0.01• V
for the device plus the thermal resistance from
= 1+
to be used in this equation normally includes
I
O(MAX)
0.01• V
I
IN(PEAK)
O
2
• f
•
O
1– D
I
O(MAX)
MAX
18717fc