LTC3609EWKG#TRPBF Linear Technology, LTC3609EWKG#TRPBF Datasheet - Page 14
![IC DC/DC CONV STP-DWN 6A 52-QFN](/photos/7/63/76369/52_qfn_05-08-1768_sml.jpg)
LTC3609EWKG#TRPBF
Manufacturer Part Number
LTC3609EWKG#TRPBF
Description
IC DC/DC CONV STP-DWN 6A 52-QFN
Manufacturer
Linear Technology
Type
Step-Down (Buck)r
Datasheet
1.LTC3609EWKGPBF.pdf
(26 pages)
Specifications of LTC3609EWKG#TRPBF
Internal Switch(s)
Yes
Synchronous Rectifier
Yes
Number Of Outputs
2
Voltage - Output
0.6 ~ 36 V
Current - Output
6A
Voltage - Input
4 ~ 32 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
52-QFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
Frequency - Switching
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
LTC3609
applicaTions inForMaTion
Once the value for L is known, the type of inductor must
be selected. High efficiency converters generally cannot
afford the core loss found in low cost powdered iron cores.
A variety of inductors designed for high current, low volt-
age applications are available from manufacturers such as
Sumida, Panasonic, Coiltronics, Coilcraft and Toko.
C
The input capacitance, C
wave current at the drain of the top MOSFET. Use a low ESR
capacitor sized to handle the maximum RMS current.
This formula has a maximum at V
I
commonly used for design because even significant de-
viations do not offer much relief. Note that ripple current
ratings from capacitor manufacturers are often based on
only 2000 hours of life which makes it advisable to derate
the capacitor.
The selection of C
ESR required to minimize voltage ripple and load step
transients. The output ripple ∆V
bounded by:
Since ∆I
is highest at maximum input voltage. Typically, once the
ESR requirement is satisfied, the capacitance is adequate
for filtering and has the necessary RMS current rating.
Multiple capacitors placed in parallel may be needed to
meet the ESR and RMS current handling requirements.
Dry tantalum, special polymer, aluminum electrolytic and
ceramic capacitors are all available in surface mount pack-
ages. Special polymer capacitors offer very low ESR but
have lower capacitance density than other types. Tantalum
RMS
IN
I
ΔV
and C
RMS
= I
OUT
OUT(MAX)
≅
L
OUT
increases with input voltage, the output ripple
I
≤ ΔI
OUT MAX
Selection
L
(
ESR+
/2. This simple worst-case condition is
)
OUT
V
V
OUT
IN
8fC
IN
is primarily determined by the
, is required to filter the square
1
OUT
V
V
OUT
IN
– 1
OUT
IN
is approximately
= 2V
OUT
, where
capacitors have the highest capacitance density but it is
important to only use types that have been surge tested
for use in switching power supplies. Aluminum electrolytic
capacitors have significantly higher ESR, but can be used
in cost-sensitive applications providing that consideration
is given to ripple current ratings and long-term reliability.
Ceramic capacitors have excellent low ESR characteris-
tics but can have a high voltage coefficient and audible
piezoelectric effects. The high Q of ceramic capacitors with
trace inductance can also lead to significant ringing. When
used as input capacitors, care must be taken to ensure
that ringing from inrush currents and switching does not
pose an overvoltage hazard to the power switches and
controller. To dampen input voltage transients, add a small
5µF to 50µF aluminum electrolytic capacitor with an ESR in
the range of 0.5Ω to 2Ω. High performance through-hole
capacitors may also be used, but an additional ceramic
capacitor in parallel is recommended to reduce the effect
of their lead inductance.
Top MOSFET Driver Supply (C
An external bootstrap capacitor, C
pin supplies the gate drive voltage for the topside MOSFET.
This capacitor is charged through diode D
when the switch node is low. When the top MOSFET turns
on, the switch node rises to V
to approximately V
to store about 100 times the gate charge required by the
top MOSFET. In most applications an 0.1µF to 0.47µF , X5R
or X7R dielectric capacitor is adequate.
Discontinuous Mode Operation and FCB Pin
The FCB pin determines whether the bottom MOSFET
remains on when current reverses in the inductor. Tying
this pin above its 0.6V threshold enables discontinuous
operation where the bottom MOSFET turns off when in-
ductor current reverses. The load current at which current
reverses and discontinuous operation begins depends on
the amplitude of the inductor ripple current and will vary
IN
+ INTV
CC
. The boost capacitor needs
IN
B
B
, D
and the BOOST pin rises
, connected to the BOOST
B
)
B
from INTV
3609fb
CC