IR3856WMTR1PBF International Rectifier, IR3856WMTR1PBF Datasheet - Page 19

• Manufacturer Part Number: IR3856WMTR1PBF
• Description: IC REG SYNC BUCK 6A 17-QFN
• Manufacturer: International Rectifier
• Series: SupIRBuck™r
• Type: Step-Down (Buck)r

Specifications of IR3856WMTR1PBF

• Internal Switch(s): Yes
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 0.7 ~ 14.4 V
• Current - Output: 6A
• Frequency - Switching: 225kHz ~ 1.65MHz
• Voltage - Input: 1.5 ~ 16 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 17-PowerVQFN
• Power - Output: 1.3W
• Part Status: Active
• Package: PQFN / 4 x 5
• Circuit: Single Output
• Iout (a): 6
• Switch Freq (khz): 0 - 750
• Input Range (v): 1.5 - 16
• Output Range (v): 0.7 - 0.9*Vin
• Ocp Otp Uvlo Pre-bias Soft Start And: PGOOD + EN + SEQ + OVD
• Server Storage: Yes
• Routers Switches: Yes
• Base Station Telecom: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: IR3856WMTR1PBFTR

V
the voltage Vc across C6 remains approximately
unchanged and the voltage at the Boot pin
becomes
A bootstrap capacitor of value 0.1uF is suitable
for most applications.
For applications with 21V input voltage, the switch
node may ring above the 25V absolute maximum
voltage rating. To prevent
using best layout practices, it may be necessary
to provide a 10ohm resistor in series with the boot
capacitor.
Input Capacitor Selection
The ripple current generated during the on time of
the upper MOSFET should be provided by the
input capacitor. The RMS value of this ripple is
expressed by:
Where:
D is the Duty Cycle
I
current.
Io is the output current.
For I
Ceramic capacitors are recommended due to
their peak current capabilities. They also feature
low ESR and ESL at higher frequency which
enables better efficiency. For this application, it is
RMS
Boot
Rev 8.0
o
Fig. 12. Bootstrap circuit to generate
is the RMS value of the input capacitor
=6A and D = 0.15, the I
≅
D =
I
V
RMS
in
V
V
+
=
in
o
V
I
o
..........
cc
∗
−
D
Vc voltage
V
∗
..........
D
(
1
..........
−
D
..........
)
..........
..........
RMS
this, in addition to
..
..........
(13)
= 2.14 A.
..........
....(12)
..........
(11)
advisable to have 2x10uF 25V ceramic capacitors
C3216X5R1E106M from TDK. In addition to
these, although not mandatory, a 1X330uF, 25V
SMD capacitor EEV-FK1E331P may also be used
as a bulk capacitor and is recommended if the
input power supply is not located close to the
converter.
Inductor Selection
The inductor is selected based on output power,
operating frequency and efficiency requirements.
A low inductor value causes large ripple current,
resulting in the smaller size, faster response to a
load transient but poor efficiency and high output
noise. Generally, the selection of the inductor
value can be reduced to the desired maximum
ripple current in the inductor
point is usually found between 20% and 50%
ripple of the output current.
For the buck converter, the inductor value for the
desired
determined using the following relation:
V
Where:
If
calculated to be 1.01μH. Select L=1 μH.
The SPM6550T-1R0M from TDK provides a
compact inductor suitable for this application
in
L
−
=
Δi ≈ 42%(I
V
(
V
o
in
=
−
L
V
V
operating
F
D
Δi
Δt
V
in
o
∗
s
o
=
=
=
=
=
Δ
Δ
)
=
Duty
∗
Switching
t
Inductor
i
Output
Turn
Maximum
;
V
o
in
), then the output inductor is
Δ
IR3856WMPbF
t
∗
cycle
on
V
=
Δ
o
i
ripple
Voltage
D
ripple
*
time
∗
F
frequency
input
s
F
1
s
..........
current
current
( i
voltage
Δ
)
. The optimum
..........
PD-97506
can
..........
19
.
be
(14)