LM20242MH/NOPB National Semiconductor, LM20242MH/NOPB Datasheet - Page 2

• Manufacturer Part Number: LM20242MH/NOPB
• Description: IC REG SYNC BUCK 2A 20TSSOP
• Manufacturer: National Semiconductor
• Series: PowerWise®r
• Type: Step-Down (Buck)r

Specifications of LM20242MH/NOPB

• Internal Switch(s): Yes
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 0.8 ~ 32 V
• Current - Output: 2A
• Frequency - Switching: 250kHz, 750kHz
• Voltage - Input: 4.5 ~ 36 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 20-TSSOP Exposed Pad, 20-eTSSOP, 20-HTSSOP
• Dc To Dc Converter Type: Step Down
• Pin Count: 20
• Input Voltage: 36V
• Output Voltage: 0.8 to 32V
• Switching Freq: 100 to 1000KHz
• Output Current: 2A
• Package Type: TSSOP EP
• Output Type: Adjustable
• Switching Regulator: Yes
• Mounting: Surface Mount
• Input Voltage (min): 4.5V
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• For Use With: LM20242EVAL - BOARD EVAL 2A POWERWISE LM20242
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -
• Lead Free Status / Rohs Status: Compliant
• Other names: *LM20242MH/NOPB; LM20242MH

www.national.com
5,6,15,16
7,8,13,14
9,10,11
Pin(s)
Connection Diagram
Ordering Information
Pin Descriptions
Order Number
EP
12
17
18
19
20
LM20242MHE
LM20242MHX
1
2
3
4
LM20242MH
Exposed
PGOOD
SS/TRK
COMP
AGND
BOOT
Name
GND
VCC
Pad
VIN
SW
FB
EN
RT
Description
Soft-Start or Tracking control input
Feedback input to the error amplifier
from the regulated output
Power good output signal
Output of the internal error amplifier and
input to the Pulse Width Modulator
Input supply voltage
Switch pin
Ground
Analog ground
Boost input for bootstrap capacitor
Output of the high voltage linear
regulator. The VCC voltage is regulated
to approximately 5.5V.
Enable or UVLO input
Internal oscillator frequency adjust input Normally biased at 550 mV. An external resistor connected between
Exposed pad
Package Type
eTSSOP-20
NSC Package Drawing
eTSSOP-20 Package
MXA20A
Top View
Application Information
An internal 5 µA current source charges an external capacitor to set
the soft-start rate. The PWM can Track to an external voltage ramp
with a low impedance source. If left open, an internal 1 ms SS ramp
is activated.
This pin is connected to the inverting input of the internal
transconductance error amplifier. An 800 mV reference is internally
connected to the non-inverting input of the error amplifier.
Open drain output indicating the output voltage is regulating within
tolerance. A pull-up resistor of 10 kΩ to 100 kΩ is recommended if this
function is used.
The loop compensation network should be connected between the
COMP pin and the AGND pin.
Nominal operating range: 4.5V to 36V.
The drain terminal of the internal Synchronous Rectifier power
NMOSFET and the source terminal of the internal Control power
NMOSFET.
Internal reference for the power MOSFETs.
Internal reference for the regulator control functions.
An internal diode from VCC to BOOT charges an external capacitor
required from SW to BOOT to power the Control MOSFET gate driver.
VCC tracks VIN up to about 7.2V. Above VIN = 7.2V, VCC is regulated
to approximately 5.5 Volts. A 0.1 µF to 1 µF ceramic decoupling
capacitor is required. The VCC pin is an output only.
An external voltage divider can be used to set the line undervoltage
lockout threshold. If the EN pin is left unconnected, a 2 µA pull-up
current source pulls the EN pin high to enable the regulator.
RT and AGND sets the internal oscillator frequency.
Exposed metal pad on the underside of the package with a weak
electrical connection to GND. Connect this pad to the PC board ground
plane in order to improve heat dissipation.
2
Package Marking
30031402
20242MH
2500 Units per Tape and Reel
250 Units per Tape and Reel
73 Units per Rail
Supplied As