MAX865EUA Maxim Integrated Products, MAX865EUA Datasheet - Page 7
![IC DC/DC CONV CHARGE-PUMP 8-UMAX](/photos/1/39/13936/406-8-msop_sml.jpg)
MAX865EUA
Manufacturer Part Number
MAX865EUA
Description
IC DC/DC CONV CHARGE-PUMP 8-UMAX
Manufacturer
Maxim Integrated Products
Type
Switched Capacitor (Charge Pump), Doubler, Invertingr
Datasheet
1.MAX865EUA.pdf
(8 pages)
Specifications of MAX865EUA
Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
2
Voltage - Output
±3.5 ~ ±12 V
Current - Output
20mA
Frequency - Switching
24kHz
Voltage - Input
1.5 ~ 6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Power - Output
330mW
Function
Inverting, Step Up
Output Voltage
- 3 V to - 12 V, 3 V to 12 V
Output Current
20 mA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
Q1146982R
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MAX865EUA+
Manufacturer:
Maxim
Quantity:
555
Part Number:
MAX865EUA+
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX865EUA+T
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX865EUA-T
Manufacturer:
AD
Quantity:
3 442
Company:
Part Number:
MAX865EUAT
Manufacturer:
MAXIM
Quantity:
6 130
A substantial voltage difference exists between (V+ -
V
and
(C1 and C2) are large with respect to their output
loads.
Larger values of reservoir capacitors (C3 and C4)
reduce output ripple. Larger values of both pump and
reservoir capacitors improve power efficiency.
To maintain the lowest output resistance, use capacitors
with low effective series resistance (ESR). The charge-
pump output resistance is a function of C1, C2, C3, and
C4’s ESR. Therefore, minimizing the charge-pump
capacitors’ ESR minimizes the total output resistance.
The MAX865 is most commonly used as a dual charge-
pump voltage converter that provides positive and neg-
ative outputs of two times a positive input voltage. The
Typical Operating Circuit shows that only four external
components are needed: capacitors C1 and C3 for the
positive pump, C2 and C4 for the negative pump. In
most applications, all four capacitors are low-cost,
3.3µF polarized electrolytics. For applications where PC
board space is at a premium and very low currents are
being drawn from the MAX865, 1µF capacitors may be
used for the pump capacitors C1 and C2, with 1µF
reservoir capacitors C3 and C4. Capacitors C2 and C4
must be rated at 12V or greater.
__________Applications Information
IN
) and V
V-
IN
if the impedances of the pump capacitors
Charge-Pump Capacitor Selection
for the positive pump, and between V+
Positive and Negative Converter
_______________________________________________________________________________________
Compact, Dual-Output Charge Pump
Paralleling multiple MAX865s (Figure 3) reduces the
output resistance of both the positive and negative con-
verters. The effective output resistance is the output
resistance of one device divided by the number of
devices. Separate C1 and C2 charge-pump capacitors
are required for each MAX865, but the reservoir capac-
itors C3 and C4 can be shared.
When under heavy loads, where V+ is sourcing current
into V- (i.e., load current flows from V+ to V-, rather than
from supply to ground), do not allow the V- supply to
pull above ground. In applications where large currents
flow from V+ to V-, use a Schottky diode (1N5817)
between GND and V-, with the anode connected to
GND (Figure 4).
Good layout is important, primarily for good noise per-
formance. To ensure good layout:
Figure 4. A Schottky diode protects the MAX865 when large
currents flow from V+ to V-.
Mount all components as close together as possible
Keep traces short to minimize parasitic inductance
and capacitance
Use a ground plane.
Heavy Output Current Loads
MAX865
Layout and Grounding
GND
Paralleling Devices
V-
7