MAX863EEE+ Maxim Integrated Products, MAX863EEE+ Datasheet - Page 5

• Manufacturer Part Number: MAX863EEE+
• Description: IC CNTRLR DC-DC HI EFF 16-QSOP
• Manufacturer: Maxim Integrated Products
• Type: Step-Up (Boost)r

Specifications of MAX863EEE+

• Internal Switch(s): No
• Synchronous Rectifier: No
• Number Of Outputs: 2
• Voltage - Output: 3.3V, 5V, Adj
• Current - Output: 1A
• Voltage - Input: 1.5 ~ 11 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-QSOP
• Power - Output: 667mW
• Output Voltage: 3.15 V to 3.45 V
• Input Voltage: 1.5 V to 11 V
• Mounting Style: SMD/SMT
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Frequency - Switching: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

The MAX863 dual, bi-CMOS, step-up, switch-mode
power-supply controller provides preset 3.3V, 5V, or
adjustable outputs. Its pulse-frequency-modulated
(PFM) control scheme combines the advantages of low
supply current at light loads and high efficiency with
heavy loads. These attributes make the MAX863 ideal
for use in portable battery-powered systems where
small size and low cost are extremely important, and
where low quiescent current and high efficiency are
needed to maximize operational battery life. Use of
external current-sense resistors and MOSFETs allows
the designer to tailor the output current and voltage
capability for a diverse range of applications.
______________________________________________________________Pin Description
_______________Detailed Description
PIN
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
SENSE1
SHDN1
SHDN2
NAME
PGND
BOOT
EXT1
EXT2
GND
LBO
V
CS1
CS2
REF
FB1
FB2
LBI
DD
_______________________________________________________________________________________
Feedback Input for DC-DC Controller 1 in Fixed-Output Mode
IC Power-Supply Input
Adjustable Feedback and Preset Output Voltage Selection Input for DC-DC Controller 1. Connect to V
for 3.3V preset output or to GND for 5V output. Connect a resistor voltage divider to adjust the output volt-
age. See the section Set the Output Voltage.
Bootstrap Low-Voltage-Oscillator Enable Input. BOOT is an active-high, logic-level input. It enables the
low-voltage oscillator to allow start-up from input voltages down to 1.5V while in a bootstrapped circuit
configuration. Connect BOOT to GND when in a non-bootstrapped configuration. If BOOT is high, V
must be connected to OUT1.
Input to the Current-Sense Comparator of DC-DC Controller 1
Gate-Drive Output of DC-DC Controller 1. Drives an external N-channel power MOSFET.
Analog Ground for Internal Reference, Feedback, and Control Circuits
High-Current Ground Return for Internal MOSFET Drivers
Gate-Drive Output of DC-DC Controller 2. Drives an external N-channel power MOSFET.
Input to the Current-Sense Amplifier of DC-DC Controller 2
Active-Low Shutdown Input for DC-DC Controller 1. Connect to V
Adjustable Feedback Input for DC-DC Controller 2. Connect a resistor voltage divider to adjust the output
voltage. See the section Set the Output Voltage.
Low-Battery Output. An open-drain N-channel MOSFET output. Sinks current when the voltage on LBI
drops below 1.25V. If unused, connect to GND.
Low-Battery Comparator Input. When the voltage on LBI drops below 1.25V, LBO sinks current. If unused,
connect to GND.
Active-Low Shutdown Input for DC-DC Controller 2. Connect to V
Reference Bypass Input. Connect a 0.1µF ceramic capacitor from REF to GND.
Dual, High-Efficiency, PFM, Step-Up
Each DC-DC controller in the MAX863 uses a one-shot-
sequenced, current-limited PFM design, as shown in
Figure 1. Referring to the Typical Operating Circuit
(Figure 2) and the switching waveforms (Figures 3a–3f),
the circuit works as follows. Output voltage is sensed
by the error comparator using either an internal voltage
divider connected to SENSE1 or an external voltage
divider connected to FB1. When the output voltage
drops, the error comparator sets an internal flip-flop.
The flip-flop turns on an external MOSFET, which allows
inductor current to ramp-up, storing energy in a mag-
netic field.
FUNCTION
DC-DC Controller
DD
DD
for normal operation.
for normal operation.
PFM Control Scheme
DD
DD
5