MAX1653ESE Maxim Integrated Products, MAX1653ESE Datasheet - Page 10

• Manufacturer Part Number: MAX1653ESE
• Description: IC CTRLR DCDC PWM STPDWN 16-SOIC
• Manufacturer: Maxim Integrated Products
• Type: Step-Down (Buck)r

Specifications of MAX1653ESE

• Internal Switch(s): No
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 2.5 ~ 5.5 V
• Current - Output: 10A
• Frequency - Switching: 150kHz, 300kHz
• Voltage - Input: 4.5 ~ 30 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (3.9mm Width)
• Power - Output: 696mW
• Output Voltage: 2.5 V to 5.5 V
• Output Current: 10 A
• Input Voltage: 4.5 V to 30 V
• Mounting Style: SMD/SMT
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

High-Efficiency, PWM, Step-Down
DC-DC Controllers in 16-Pin QSOP
It’s easy to adapt the basic MAX1653 single-output 3.3V
buck converter (Figure 1) to meet a wide range of appli-
cations with inputs up to 30V (limited by choice of exter-
nal MOSFET). Simply substitute the appropriate
components from Table 1 (candidate suppliers are pro-
vided in Table 2). These circuits represent a good set of
trade-offs among cost, size, and efficiency while staying
within the worst-case specification limits for stress-relat-
ed parameters such as capacitor ripple current.
Don’t change the frequency of these circuits without
first recalculating component values (particularly induc-
tance value at maximum battery voltage).
For a discussion of dual-output circuits using the
MAX1652 and MAX1654, see Figure 9 and the
Secondary Feedback-Regulation Loop section.
Figure 1. Standard 3.3V Application Circuit (see Table 1 for Component Values)
10
NOTE: KEEP CURRENT-SENSE
(OPTIONAL)
C1
INPUT
LOW-NOISE
______________________________________________________________________________________
0.01 F
CONTROL
CONTROL
ON/OFF
LINES SHORT AND CLOSE
TOGETHER. SEE FIGURE 8.
Standard Application Circuits
C6
6
2
1
C7
0.1 F
SHDN
SKIP
SS
10
7
FB
MAX1653
V+
5
SYNC
11
VL
J1
150kHz/300kHz
JUMPER
PGND
CSH
GND
BST
CSL
REF
DH
LX
DL
16
14
15
13
12
8
9
4
3
D2
CMPSH-3
C3
0.1 F
C5
0.33 F
The MAX1652 family are BiCMOS, switch-mode power-
supply controllers designed primarily for buck-topology
regulators in battery-powered applications where high
efficiency and low quiescent supply current are critical.
The parts also work well in other topologies such as
boost, inverting, and Cuk due to the flexibility of their
floating high-speed gate driver. Light-load efficiency is
enhanced by automatic idle-mode operation—a vari-
able-frequency pulse-skipping mode that reduces
losses due to MOSFET gate charge. The step-down
power-switching circuit consists of two N-channel
MOSFETs, a rectifier, and an LC output filter. The out-
put voltage is the average of the AC voltage at the
switching node, which is adjusted and regulated by
changing the duty cycle of the MOSFET switches. The
gate-drive signal to the N-channel high-side MOSFET
must exceed the battery voltage and is provided by a
flying capacitor boost circuit that uses a 100nF capaci-
tor connected to BST.
Q1
Q2
D1
C4
4.7 F
L1
Detailed Description
R1
C2
REF OUTPUT
+2.5V AT 100 A
+5V AT
5mA
+3.3V
OUTPUT
GND
OUT