LM2576D2T-015 ON Semiconductor, LM2576D2T-015 Datasheet - Page 10
![IC REG SW 3A 15V STEPDOWN D2PAK](/photos/36/39/363977/to263-5_sml.jpg)
LM2576D2T-015
Manufacturer Part Number
LM2576D2T-015
Description
IC REG SW 3A 15V STEPDOWN D2PAK
Manufacturer
ON Semiconductor
Type
Step-Down (Buck)r
Datasheet
1.LM2576D2T-ADJR4G.pdf
(28 pages)
Specifications of LM2576D2T-015
Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
15V
Current - Output
3A
Frequency - Switching
52kHz
Voltage - Input
7 ~ 40 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
D²Pak, TO-263 (5 leads + tab)
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Power - Output
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Procedure (Fixed Output Voltage Version) In order to simplify the switching regulator design, a step−by−step
design procedure and some examples are provided.
Given Parameters:
1. Controller IC Selection
2. Input Capacitor Selection (C
3. Catch Diode Selection (D1)
4. Inductor Selection (L1)
V
V
I
According to the required input voltage, output voltage and
current, select the appropriate type of the controller IC output
voltage version.
To prevent large voltage transients from appearing at the input
and for stable operation of the converter, an aluminium or
tantalum electrolytic bypass capacitor is needed between the
input pin +V
located close to the IC using short leads. This capacitor should
have a low ESR (Equivalent Series Resistance) value.
A. Since the diode maximum peak current exceeds the
B. The reverse voltage rating of the diode should be at least
A. According to the required working conditions, select the
B. From the appropriate inductor selection guide, identify the
C. Select an appropriate inductor from the several different
Load(max)
out
in(max)
regulator maximum load current the catch diode current
rating must be at least 1.2 times greater than the maximum
load current. For a robust design the diode should have a
current rating equal to the maximum current limit of the
LM2576 to be able to withstand a continuous output short
1.25 times the maximum input voltage.
correct inductor value using the selection guide from
Figures 18 to 22.
inductance region intersected by the Maximum Input
Voltage line and the Maximum Load Current line. Each
region is identified by an inductance value and an inductor
code.
manufacturers part numbers listed in Table 2.
The designer must realize that the inductor current rating
must be higher than the maximum peak current flowing
through the inductor. This maximum peak current can be
calculated as follows:
where t
For additional information about the inductor, see the
inductor section in the “Application Hints” section of
this data sheet.
= Regulated Output Voltage (3.3 V, 5.0 V, 12 V or 15 V)
= Maximum Input Voltage
= Maximum Load Current
I
on
p(max)
in
is the “on” time of the power switch and
and ground pin GND. This capacitor should be
+
I
t on
Load(max)
Procedure
+
V out
V
in
in
)
)
x 1.0
f osc
V in –V out t on
2L
http://onsemi.com
LM2576
10
Given Parameters:
1. Controller IC Selection
2. Input Capacitor Selection (C
3. Catch Diode Selection (D1)
4. Inductor Selection (L1)
V
V
I
According to the required input voltage, output voltage,
current polarity and current value, use the LM2576−5
controller IC
A 100 mF, 25 V aluminium electrolytic capacitor located near
to the input and ground pins provides sufficient bypassing.
A. For this example the current rating of the diode is 3.0 A.
B. Use a 20 V 1N5820 Schottky diode, or any of the
A. Use the inductor selection guide shown in Figures 19.
B. From the selection guide, the inductance area intersected
C. Inductor value required is 100 mH. From Table 2, choose
Load(max)
out
in(max)
suggested fast recovery diodes shown in Table 1.
by the 15 V line and 3.0 A line is L100.
an inductor from any of the listed manufacturers.
= 5.0 V
= 15 V
= 3.0 A
Example
in
)