IL610A-1E NVE, IL610A-1E Datasheet
IL610A-1E
Specifications of IL610A-1E
Related parts for IL610A-1E
IL610A-1E Summary of contents
Page 1
... Valley View Road, Eden Prairie, MN 55344-3617 IL600A Series Features 10 Mbps Data Rate Flexible Inputs with Very Wide Input Voltage Range Failsafe Output (logic high output for zero coil current) Output Enable (IL610A) 3 Power Supply 2500 V Isolation (1 minute) RMS Low Power Dissipation 40° ...
Page 2
... Rated Voltage (1 min.; SOIC & PDIP) Safety and Approvals IEC61010-2001 TUV Certificate Numbers: Classification: Reinforced Insulation Model IL610A-2, IL611A-2, IL612A-2 IL610A-3, IL611A-3, IL612A-3 UL 1577 Component Recognition Program File Number: E207481 Rated 2,500V for 1 minute (SOIC, PDIP) RMS Soldering Profile Per JEDEC J-STD-020C Electrostatic Discharge Sensitivity This product has been tested for electrostatic sensitivity to the limits stated in the specifications ...
Page 3
... IL610A Pin Connections internal connection 2 IN+ Coil connection 3 IN Coil connection internal connection 5 GND Ground return for OUT Data out Output enable Internally held low with 100 Supply Voltage DD IL611A Pin Connections Channel 1 coil connection Channel 1 coil connection Channel 2 coil connection ...
Page 4
... V to 5.5 V unless otherwise stated. Symbol Min. Typ. Z 85||9 COIL TC R 0.2 COIL I 0.5 INH I 5 3.5 INL IL610A IL611A IL612A, I DD1 IL612A, I DD2 IL610A, I 1.3 DD IL611A, I 2.6 DD IL612A, I 1.3 DD1 IL612A, I 1.3 DD2 0 Switching Specifications at 5V Symbol Min. ...
Page 5
... To calculate the value of the protection resistor (R1), use Ohm’s law as shown in the examples below. Note that only the magnitude of the voltage across the coil is important; the absolute values 10nF R limit 15pF 2 Test Circuit 2 (Differential) 5 IL600A Series + IL610A GND GND GND and V are arbitrary ...
Page 6
... Test Circuit 1). Single-Ended or Differential Input The IL610A and IL611A can be run with single-ended or differential inputs. In differential mode, coil current reverses each cycle. In single-ended mode, a “boost capacitor” placed across the current limit resistor provides pulsed current reversal for correct operation ...
Page 7
In differential mode, erosion takes place in both directions as each current cycle reverses and has a net effect of zero up to the fuse current. A current of more than 100 mA will cause the coil to irreparably fuse ...
Page 8
... Similarly, when using IL600A-Series devices, the designer should be aware that it is the voltage magnitude across the coil that creates the current, not just the value of the input voltage. To illustrate this point, consider the single-ended non-inverting and inverting cases. Bridge Output Response ...
Page 9
... IL610A IL610A Data In Data boost boost GND GND 1 1 Inverting Circuit Inverting Circuit + boost boost IL610A IL610A Data In Data In GND GND 1 1 Non-Inverting Circuit Non-Inverting Circuit Figure 5. Inverting and Non-Inverting circuits 9 IL600A Series Data Out Data Out C C ...
Page 10
... The shield absorbs surrounding stray flux until it becomes saturated. At saturation the shield is transparent to external applied fields, and the GMR sensor may react to the field. To compensate for this effect, IsoLoop Isolators use Wheatstone Bridge structures that are only sensitive to differential magnetic fields. ...
Page 11
... IL610A coil resistance of approximately 85 characteristic impedance of most cables. The circuit is intrinsically open circuit failsafe because the IL610A is guaranteed to switch to the high state when the coil input current is less than 500 µA. For higher speed, a faster output device (such the CMOS-output IL600-Series Isolators) are needed as well as possibly better impedance matching ...
Page 12
... IL610A 10K 0. 10K 0. IL610A IL610A IL610A GND 1 12 IL600A Series + 47nF Monitor Out GND System Error Notes application specific boost All other capacitors are 47 nF ceramic ...
Page 13
P82B96 SDA Isolation Nodes This circuit provides bidirectional isolation of I²C bus signals with no restrictions on data rate and none of the I²C bus latch-up problems common with other isolation circuits. ...
Page 14
Package Drawings, Dimensions and Specifications 8-pin MSOP 0.114 (2.90) 0.122 (3.10) 0.114 (2.90) 0.189 (4.80) 0.197 (5.00) 0.122 (3.10) 0.010 (0.25) 0.016 (0.40) 8-pin SOIC Package 0.189 (4.8) 0.197 (5.0) 0.228 (5.8) 0.150 (3.8) 0.244 (6.2) 0.157 (4. ...
Page 15
... Transmit Channels 612 = 1 Transmit Channel, 1 Receive Channel Product Family IL = Isolators 15 IL600A Series IL610A Valid Part Numbers IL610A-1E IL610A-2E IL610A-3E IL610A-5 IL610A-1ETR7 IL610A-3ETR7 IL610A-1ETR13 IL610A-3ETR13 IL611A Valid Part Numbers IL611A-1E IL611A-2E IL611A-3E IL611A-1ETR7 IL611A-3ETR7 IL611A-1ETR13 IL611A-3ETR13 IL612A Valid Part Numbers IL612A-2E IL612A-3E ...
Page 16
Revision History ISB-DS-001-IL600A-T September 2010 ISB-DS-001-IL600A-S ISB-DS-001-IL600A-R ISB-DS-001-IL600A-Q ISB-DS-001-IL600A-P ISB-DS-001-IL600A-O ISB-DS-001-IL600A-N ISB-DS-001-IL600A-M ISB-DS-001-IL600A-L ISB-DS-001-IL600A-K ISB-DS-001-IL600A-J ISB-DS-001-IL600A-I ISB-DS-001-IL600A-H ISB-DS-001-IL600A-G ISB-DS-001-IL600A-F ISB-DS-001-IL600A-E Changes Additional changes to pin spacing specification on MSOP package drawing. Changes Changed pin spacing specification on MSOP package drawing. ...
Page 17
... Corporation for its use, nor for any infringement of patents, nor rights or licenses granted to third parties, which may result from its use. No license is granted by implication, or otherwise, under any patent or patent rights of NVE Corporation. NVE Corporation does not authorize, nor warrant, any NVE Corporation product for use in life support devices or systems or other critical applications, without the express written approval of the President of NVE Corporation ...