SI8410BB-D-IS Silicon Laboratories Inc, SI8410BB-D-IS Datasheet - Page 13

• Manufacturer Part Number: SI8410BB-D-IS
• Description: IC ISOLATOR 1CH 5.5V 8-SOIC
• Manufacturer: Silicon Laboratories Inc
• Series: ISOpror

Specifications of SI8410BB-D-IS

• Number Of Channels: 1
• Package / Case: 8-SOIC (3.9mm Width)
• Inputs - Side 1/side 2: 1/0
• Isolation Rating: 2500Vrms
• Voltage - Supply: 2.7 V ~ 5.5 V
• Data Rate: 150Mbps
• Propagation Delay: 6ns
• Output Type: Logic
• Operating Temperature: -40°C ~ 125°C
• Mounting Style: SMD/SMT
• Propagation Delay Time: 6 ns
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Supply Current: 6 mA
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 336-1752-5

Table 5. Electrical Characteristics
(V
Table 6. Regulatory Information*
Parameter
Si8410Bx, Si8420Bx, Si8421Bx
Maximum Data Rate
Minimum Pulse Width
Propagation Delay
Pulse Width Distortion
|t
Propagation Delay Skew
Channel-Channel Skew
All Models
Output Rise Time
Output Fall Time
Common Mode Transient
Immunity
Start-up Time
Notes:
CSA
The Si84xx is certified under CSA Component Acceptance Notice 5A. For more details, see File 232873.
61010-1: Up to 300 V
60950-1: Up to 130 V
VDE
The Si84xx is certified according to IEC 60747-5-2. For more details, see File 5006301-4880-0001.
60747-5-2: Up to 560 V
UL
The Si84xx is certified under UL1577 component recognition program. For more details, see File E257455.
Rated up to 2500 V
*Note: Regulatory Certifications apply to 2.5 kV
PLH
DD1
1. Specifications in this table are also valid at VDD1 = 2.6 V and VDD2 = 2.6 V when the operating temperature range is
2. The nominal output impedance of an isolator driver channel is approximately 85 , ±40%, which is a combination of the
3. t
4. Start-up time is the time period from the application of power to valid data at the output.
= 2.70 V, V
- t
constrained to T
value of the on-chip series termination resistor and channel resistance of the output driver FET. When driving loads
where transmission line effects will be a factor, output pins should be appropriately terminated with controlled
impedance PCB traces.
the same supply voltages, load, and ambient temperature.
For more information, see "5. Ordering Guide" on page 25.
PSK(P-P)
PHL
|
4
is the magnitude of the difference in propagation delay times measured between different units operating at
DD2
= 2.70 V, T
RMS
A
RMS
RMS
= 0 to 85 °C.
peak
isolation voltage for basic insulation.
3
reinforced insulation working voltage; up to 600 V
reinforced insulation working voltage; up to 600 V
for basic insulation working voltage.
A
= –40 to 125 °C)
t
t
Symbol
PHL
PSK(P-P)
CMTI
PWD
t
1
t
PSK
SU
, t
t
t
r
f
(Continued)
PLH
RMS
rated devices which are production tested to 3.0 kV
Test Condition
V
See Figure 1
See Figure 1
I
C
C
= V
L
L
Rev. 1.3
= 15 pF
= 15 pF
DD
or 0 V
Min
3.0
—
—
—
—
—
—
—
—
0
RMS
RMS
basic insulation working voltage.
basic insulation working voltage.
Si8410/20/21
Typ
6.0
1.5
2.0
0.5
4.8
3.2
—
—
25
15
RMS
for 1 sec.
Max
150
6.0
9.5
2.5
3.0
1.8
6.5
4.6
40
—
Mbps
kV/µs
Unit
ns
ns
ns
ns
ns
ns
ns
µs
13