IL710-2E NVE, IL710-2E Datasheet
![ISOLATOR HS MAGN DIGITAL 8DIP](/photos/7/65/76563/390-8-dip_sml.jpg)
IL710-2E
Specifications of IL710-2E
Related parts for IL710-2E
IL710-2E Summary of contents
Page 1
... The symmetric magnetic coupling barrier provides a typical propagation delay of only 10 ns and a pulse width distortion as low as 300 ps (0.3 ns), achieving the best specifications of any isolator. Typical transient immunity of 30 kV/µs is unsurpassed. The IL710 is ideal for isolating applications such as PROFIBUS, RS-485, and RS-422. ...
Page 2
... Input Voltage Output Voltage Output Current Drive Lead Solder Temperature ESD Recommended Operating Conditions Parameters Ambient Operating Temperature IL710 and IL710S IL710T Supply Voltage Logic High Input Voltage Logic Low Input Voltage Input Signal Rise and Fall Times Insulation Specifications Parameters ...
Page 3
... IL710 Pin Connections 1 V Supply voltage DD1 2 IN Data internal connection 4 GND Ground return for V 1 DD1 5 GND Ground return for V 2 DD2 6 OUT Data Out Output enable Internally held low with 100 kΩ Supply voltage DD2 Timing Diagram V DD1 IN NC ...
Page 4
... Propagation Delay Enable to Output (Low to High Impedance) Propagation Delay Enable to Output (High Impedance to High) Propagation Delay Enable to Output (High Impedance to Low) (2) Pulse Width Distortion IL710 and IL710T IL710S (8) Pulse Jitter (3) Propagation Delay Skew Output Rise Time (10%–90%) Output Fall Time (10%–90%) ...
Page 5
... Propagation Delay Enable to Output (Low to High Impedance) Propagation Delay Enable to Output (High Impedance to High) Propagation Delay Enable to Output (High Impedance to Low) (2) Pulse Width Distortion IL710 and IL710T IL710S (3) Propagation Delay Skew Output Rise Time (10%–90%) Output Fall Time (10%–90%) Common Mode Transient Immunity (4) ...
Page 6
... Worst- case channel-to-channel skew in an IL700 Isolator is only 3 ns, which is ten times better than any optocoupler. IL700 Isolators have a maximum propagation delay skew of 6 ns, which is five times better than any optocoupler. 6 IL710 and 1 pins. DD ...
Page 7
... Application Diagrams Isolated PROFIBUS / RS-485 Isolation Boundary IL710 IL710 IL710 NVE offers a unique line of PROFIBUS/RS-485 transceivers, but IL710 isolators can also be used as part of multi-chip designs using non- isolated PROFIBUS transceivers. RS-485 Truth Table TXD RTS Note: ISL8485 V and V should be decoupled with ...
Page 8
... In this circuit, power is supplied by USB bus power on one side of the isolation barrier, and the USB node’s external supply on the other side of the barrier. IL700 Isolators are specified with just 3 ns worst-case pulse width distortion. Isolation Boundary 5 x IL710 8 IL710 Power supplied by USB ...
Page 9
... IL710 0.054 (1.37) 0.069 (1.75) 0.004 (0.10) 0.040 (1.0) 0.010 (0.25) 0.060 (1.5) NOTE: Pin spacing is a BASIC dimension; tolerances do not accumulate ...
Page 10
... IL 710 TR13 Valid Part Numbers IL710-1E IL710S-1E Bulk Packaging IL710T-1E Blank = Tube TR7 = 7" Tape and Reel IL710-2 TR13 = 13" Tape and Reel IL710T-2 IL710-2E Package IL710T-2E Blank = 80/20 Tin/Lead Plating E = RoHS Compliant IL710-3 IL710S-3 Package Type IL710T MSOP IL710- PDIP IL710S- 0.15" ...
Page 11
... Corrected PWD spec. on Isolated USB application diagram (p. 8). • Changed lower limit of length on PDIP package drawing and ISB-DS-001-IL710-N Changes • Changed IL710T output quiescent supply current specifications. ISB-DS-001-IL710-M Changes • Changed ordering information to reflect that devices are now fully RoHS compliant with ...
Page 12
... No license is granted by implication, or otherwise, under any patent or patent rights of NVE Corporation. NVE Corporation does not authorize, nor warrant, any NVE Corporation product for use in life support devices or systems or other critical applications, without the express written approval of the President of NVE Corporation. Specifications are subject to change without notice. ISB-DS-001-IL710-V September 2010 12 IL710 ...