HCPL-0730-000E Avago Technologies US Inc., HCPL-0730-000E Datasheet - Page 11

• Manufacturer Part Number: HCPL-0730-000E
• Description: OPTOCOUPLER DARL-OUT 2CH 8-SOIC
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-0730-000E

• Input Type: DC
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 2, Unidirectional
• Current - Output / Channel: 60mA
• Data Rate: 100KBd
• Propagation Delay High - Low @ If: 25µs @ 500µA
• Current - Dc Forward (if): 20mA
• Output Type: Open Collector
• Mounting Type: Surface Mount
• Isolation Voltage: 3750 Vrms
• Maximum Continuous Output Current: 60 mA
• Maximum Forward Diode Current: 20 mA
• Output Device: Darlington With Base
• Configuration: 2 Channel
• Current Transfer Ratio: 2600 %
• Maximum Baud Rate: 100 KBps
• Maximum Forward Diode Voltage: 1.7 V
• Maximum Reverse Diode Voltage: 5 V
• Maximum Input Diode Current: 20 mA
• Maximum Power Dissipation: 135 mW
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• No. Of Channels: 2
• Optocoupler Output Type: Photodarlington
• Input Current: 12mA
• Output Voltage: 7V
• Opto Case Style: SOIC
• No. Of Pins: 8
• Ctr Max: 5000%
• Ctr Min: 300%
• Rohs Compliant: Yes
• Number Of Elements: 2
• Reverse Breakdown Voltage: 5V
• Forward Voltage: 1.7V
• Forward Current: 20mA
• Package Type: SOIC
• Collector Current (dc) (max): 60mA
• Power Dissipation: 135mW
• Pin Count: 8
• Mounting: Surface Mount
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 516-1641-5

Package Characteristics
*All Typical values at T
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equip-
ment level safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage. ”
Notes:
10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 6000 V rms for 1 second (leakage
11. Measured between the LED anode and cathode shorted together and pins 5 through 8 shorted together.
12. Derate linearly above 65°C free-air temperature at a rate of 2.3 mW/°C for the SO-8 package.
11
1. Pin 5 should be the most negative voltage at the detector side.
2. Each channel.
3. DC CURRENT TRANSFER RATIO (CTR) is defined as the ratio of output collector current, I
4. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together, and pins 5, 6, 7, and 8 shorted together.
5. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together.
6. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dV
7. In applications where dV/dt may exceed 50,000 V/µs (such as static discharge) a series resistor, R
8. Use of a 0.1 µF bypass capacitor connected between pins 5 and 8 adjacent to the device is recommended.
9. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 4500 V rms for 1 second (leakage
Parameter
Input-Output Momentary
Withstand Voltage**
Resistance
(Input-Output)
Capacitance
(Input-Output)
Input-Input Insulation
Leakage Current
Input-Input Insulation
Leakage Current
Capacitance
(Input-Input)
sure that the output will remain in a Logic High state
level is the maximum tolerable (negative) dV
(i.e., V
tor IC from destructively high surge currents. The recommended value is R
detection current limit,
detection current limit,
O
< 0.8 V).
Option 020
A
= 25°C unless otherwise noted.
Symbol
V
R
C
R
C
I
I
I
ISO
I-I
I-O
I-O
I-O
I-O
I-I
I-I
< 5 µA).
< 5 µA).
CM
/dt of the common mode pulse, V
Device
2730
2731
2730
2731
0730
0731
HCPL-
0.005
3750
5000
Min.
Typ.*
0.03
0.25
10
10
0.6
(i.e., V
12
11
CC
= 110 Ω.
O
Max.
> 2.0 V). Common mode transient immunity in a Logic Low
CM
, to assure that the output will remain in a Logic Low state
V rms
Units
O
µA
pF
pF
, to the forward LED input current, I
Ω
Ω
CM
CC
RH ≤50%,
t = 1 min.,
T
V
RH ≤45%
f = 1 MHz
RH ≤45%
V
/dt of the common mode pulse, V
, should be included to protect the detec-
A
Test Conditions
I-O
I-I
= 25°C
= 500 VDC
= 500 VDC
F
, times 100%.
Fig.
CM
, to as-
4, 10
Note
4, 9
11
4
5
5
5