HCPL-3140-000E Avago Technologies US Inc., HCPL-3140-000E Datasheet - Page 4

• Manufacturer Part Number: HCPL-3140-000E
• Description: OPTOCOUPLER IGBT DRIVE 0.4A 8DIP
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-3140-000E

• Package / Case: 8-DIP (0.300", 7.62mm)
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 600mA
• Propagation Delay High - Low @ If: 300ns @ 8mA
• Current - Dc Forward (if): 25mA
• Input Type: DC
• Output Type: Push-Pull, Totem-Pole
• Mounting Type: Through Hole
• Isolation Voltage: 3750 Vrms
• Maximum Fall Time: 0.05 us
• Maximum Forward Diode Current: 25 mA
• Minimum Forward Diode Voltage: 1.2 V
• Output Device: Logic Gate Photo IC
• Configuration: 1 Channel
• Maximum Forward Diode Voltage: 1.8 V
• Maximum Reverse Diode Voltage: 5 V
• Maximum Power Dissipation: 250 mW
• Maximum Operating Temperature: + 100 C
• Minimum Operating Temperature: - 40 C
• No. Of Channels: 1
• Optocoupler Output Type: Gate Drive
• Input Current: 12mA
• Output Voltage: 30V
• Opto Case Style: DIP
• No. Of Pins: 8
• Common Mode Ratio: 10 KV/uS
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 516-1583-5

Recommended Pb-Free IR Profile
Solder Reflow Temperature Profile
TEMPERATURE
IEC/EN/DIN EN 60747-5-2 Insulation Characteristics (HCPL-3140 Option 060)
* Refer to the optocoupler section of the Isolation and Control Components Designer’s Catalog, under Product Safety Regulations section IEC/EN/
** Refer to the following figure for dependence of P
4
Partial discharge < 5 pC
Description
Installation classification per DIN VDE 0110/1.89, Table 1
for rated mains voltage 150 V
for rated mains voltage 300 V
for rated mains voltage 600 V
Climatic Classification
Pollution Degree (DIN VDE 0110/1.89)
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method b*
V
t
Input to Output Test Voltage, Method a*
V
Highest Allowable Overvoltage
(Transient Overvoltage t
Safety-limiting values - maximum values allowed in the
event of a failure.
Case Temperature
Input Current**
Output Power**
Insulation Resistance at T
m
DIN EN 60747-5-2 for a detailed description of Method a and Method b partial discharge test profiles.
ROOM
IORM
IORM
=1 sec, Partial discharge < 5 pC
x 1.875=V
x 1.5=V
NOTES:
THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX.
T
T
T
smax
smax
smin
300
200
100
T
T
25
0
p
L
= 200 °C, T
0
Note: Non-halide flux should be used.
Note: Non-halide flux should be used.
150 - 200 °C
217 °C
PR
PREHEATING RATE 3°C + 1°C/–0.5°C/SEC.
REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC.
160°C
150°C
140°C
PR
, Type and Sample Test, t
, 100% Production Test with
t 25 °C to PEAK
3 °C/SEC. MAX.
60 to 180 SEC.
smin
PREHEAT
RAMP-UP
= 150 °C
t
s
50
ini
260 +0/-5 °C
S
3°C + 1°C/–0.5°C
= 10 sec)
, V
PREHEATING TIME
150°C, 90 + 30 SEC.
TIME
IO
rms
rms
rms
= 500 V
2.5°C ± 0.5°C/SEC.
t
t
L
100
p
TIME (SECONDS)
m
TIME WITHIN 5 °C of ACTUAL
PEAK TEMPERATURE
20-40 SEC.
60 to 150 SEC.
=60 sec,
S
RAMP-DOWN
6 °C/SEC. MAX.
and I
TEMP.
PEAK
245°C
S
150
on ambient temperature.
SEC.
SEC.
30
30
50 SEC.
SOLDERING
200°C
TIME
200
PEAK
TEMP.
240°C
TIGHT
TYPICAL
LOOSE
TEMP.
PEAK
230°C
P
250
Symbol
I
S, OUTPUT
V
S,INPUT
V
V
V
IORM
IOTM
R
T
PR
PR
S
S
Regulatory Information
The HCPL-3140/HCPL-0314 have
been approved by the following
organizations:
IEC/EN/DIN EN 60747-5-2
Approved under:
IEC 60747-5-2:1997 + A1:2002
EN 60747-5-2:2001 + A1:2002
DIN EN 60747-5-2 (VDE 0884
(Option 060 only)
UL
Approval under UL 1577,
component recognition program
up to V
E55361.
CSA
Approval under CSA Component
Acceptance Notice #5, File CA
88324.
Teil 2):2003-01
Characteristic
55/100/21
ISO
1181
6000
>10
I - IV
I - III
630
945
175
230
600
I-II
2
= 2500 V
9
rms
. File
V
V
V
V
Unit
mW
mA
peak
peak
peak
peak
C