HCPL-4504-320E Avago Technologies US Inc., HCPL-4504-320E Datasheet - Page 8
![OPTOCOUPLER 1CH UL GAASP 8SMD GW](/photos/15/83/158318/dual_inline_gull_wing_sml.jpg)
HCPL-4504-320E
Manufacturer Part Number
HCPL-4504-320E
Description
OPTOCOUPLER 1CH UL GAASP 8SMD GW
Manufacturer
Avago Technologies US Inc.
Datasheet
1.HCPL-4504-000E.pdf
(19 pages)
Specifications of HCPL-4504-320E
Input Type
DC
Package / Case
8-SMD (300 mil)
Voltage - Isolation
5000Vrms
Number Of Channels
1, Unidirectional
Current - Output / Channel
8mA
Propagation Delay High - Low @ If
200ns @ 16mA
Current - Dc Forward (if)
25mA
Output Type
Open Collector
Mounting Type
Surface Mount, Gull Wing
Isolation Voltage
3750 Vrms
Maximum Forward Diode Current
12 mA
Output Device
Phototransistor
Configuration
1 Channel
Current Transfer Ratio
65 %
Maximum Baud Rate
1 MBps
Maximum Forward Diode Voltage
1.7 V
Maximum Reverse Diode Voltage
5 V
Maximum Input Diode Current
25 mA
Maximum Power Dissipation
100 mW
Maximum Operating Temperature
+ 100 C
Minimum Operating Temperature
- 55 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HCPL-4504-320E
Manufacturer:
AVAGO
Quantity:
15 000
Regulatory Information
The devices contained in this data sheet have been approved by the following agencies:
Insulation and Safety Related Specifi cations
All Avago data sheets report the creepage and clearance
inherent to the optocoupler component itself. These di-
mensions are needed as a starting point for the equip-
ment designer when determining the circuit insulation
requirements.
However, once mounted on a printed circuit board, mini-
mum creepage and clearance requirements must be
met as specifi ed for individual equipment standards. For
8
Agency/Standard
Underwriters Laboratories (UL)
Recognized under UL1577,
Component Recognition Program,
Category FPQU2, File E55361
Canadian Standards Association (CSA)
File CA88324
IEC/EN/DIN EN 60747-5-2
Approved under:
IEC 60747-5-2:1997 + A1:2002
EN 60747-5-2:2001 + A1:2002
DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01
Parameter
Minimum External
Air Gap
(External Clearance)
Minimum External
Tracking
(External Creepage)
Minimum Internal
Plastic Gap
(Internal Clearance)
Minimum Internal
Tracking (Internal
Creepage)
Tracking Resistance
(Comparative
Tracking Index)
Isolation Group
Symbol
L(101)
L(102)
CTI
HCPL-
≥175
4504
0.08
7.1
7.4
NA
IIIa
UL1577
Component
Acceptance
Notice #5
-400E/-600E
HCPL-
≥175
J454
8.0
8.0
0.5
NA
IIIa
HCPL-4504
3750 Vrms /
1 minute,
Option 020 5000
Vrms / 1 minute
3750 Vrms /
1 minute,
Option 020 5000
Vrms / 1 minute
Option 060
V
IORM
HCPL-J454
Value
All other
options
≥175
= 630 Vpeak
7.4
8.0
0.5
NA
IIIa
creepage, the shortest distance path along the surface
of a printed circuit board between the solder fi llets of
the input and output leads must be considered. There
are recommended techniques such as grooves and ribs
which may be used on a printed circuit board to achieve
desired creepage and clearances. Creepage and clear-
ance distances will also change depending on factors
such as pollution degree and insulation level.
HCPL-
≥175
0454
0.08
4.9
4.8
NA
IIIa
HCPL-J454
3750 Vrms /
1 minute
3750 Vrms /
1 minute
V
Vpeak
IORM
HCNW
≥200
4504
10.0
9.6
1.0
4.0
IIIa
= 891
Units Conditions
mm
mm
mm
mm
Volts
HCPL-0454
3750 Vrms /
1 minute
3750 Vrms /
1 minute
Option 060
V
Vpeak
IORM
Measured from input ter-
minals to output terminals,
shortest distance through air.
Measured from input ter-
minals to output terminals,
shortest distance path along
body.
Through insulation distance,
conductor to conductor,
usually the direct distance
between the photoemitter
and photodetector inside the
optocoupler cavity.
Measured from input ter-
minals to output terminals,
along internal cavity.
DIN IEC 112/VDE 0303 Part 1
Material Group (DIN VDE
0110, 1/89, Table 1)
= 560
HCNW4504
5000 Vrms /
1 minute
5000 Vrms /
1 minute
V
Vpeak
IORM
= 1414