HCPL-4100-000E Avago Technologies US Inc., HCPL-4100-000E Datasheet - Page 10
HCPL-4100-000E
Manufacturer Part Number
HCPL-4100-000E
Description
OPTOCOUPLER TRANSMITTR 20MA 8DIP
Manufacturer
Avago Technologies US Inc.
Type
Transmitterr
Datasheet
1.HCPL-4100-000E.pdf
(12 pages)
Specifications of HCPL-4100-000E
Package / Case
8-DIP (0.300", 7.62mm)
Voltage - Isolation
3750Vrms
Input Type
DC
Voltage - Supply
4.5 V ~ 20 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Through Hole
Logic Gate Type
Inverter
Maximum Baud Rate
0.02 MBd
Configuration
1 Channel
Isolation Voltage
3750 Vrms
Output Type
Open Collector
Maximum Propagation Delay Time
1600 ns
Maximum Forward Diode Current
7 mA
Maximum Continuous Output Current
30 mA
Maximum Power Dissipation
360 mW
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
No. Of Channels
1
Optocoupler Output Type
Transistor
Input Current
250µA
Output Voltage
27V
Opto Case Style
DIP
No. Of Pins
8
Data Rate Max
24Kbps
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
516-1546-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HCPL-4100-000E
Manufacturer:
AVAGO
Quantity:
5 000
Part Number:
HCPL-4100-000E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Figure 13. Recommended Non-Isolated Active Receiver with HCPL-4100 Isolated Transmitter for Simplex Point to Point 20 mA Current Loop.
25% distortion data rate at different V
tion data rate is defined as that rate at which 25% distortion
occurs to output bit interval with respect to the input bit
interval. Maximum data rate (dotted line) is restricted by
device character is tics. An input Non-Return-to-Zero (NRZ)
test waveform of 16 bits (0000001011111101) was used
for data rate distortion measure ments. Enhanced speed
performance of the loop system can be obtained with lower
V
when loop current is supplied through a resistor instead
of by a current source, an additional series termination
resistance equal to the characteristic line impedance can
be used at the HCPL-4100 transmitter end to enhance
speed of response by approximately 20%.
Figure 14. Minimum Required Supply Voltage, V
Loop Length for Current Loop Circuit of Figure 13.
10
CC
supply levels, as illustrated in Figure 15. In addition,
40
36
32
28
24
20
16
12
8
4
0
L – LOOP LENGTH (ONE DIRECTION) METERS
0
V
R
I
V
V
T
LOOP
CC
MARK
SAT
A
CABLE
= 25 °C
= 0.00212
= 1.5 Vdc (CURRENT SOURCE)
= 20 mA
= 2.7 Vdc (HCPL-4100)
= 0.05296
100
— (L) + 5.7 V
m
V
Ω /m
1000
10000
CC
CC
, vs.
values. 25% distor-
The cable used contained five pairs of unshielded, twisted,
22 AWG wire (Dearborn #862205). Loop current is 20 mA
nominal. Input and output logic supply voltages are 5 V
dc.
Full Duplex
The full duplex point-to-point communication of Fig-
ure 16 uses a four wire system to provide simultane-
ous, bidirectional data communication between local
and remote equipment. The basic application uses
two simplex point-to-point loops which have two
separate, active, non-isolated units at one common
end of the loops. The other end of each loop is isolated.
Figure 15. Typical Data Rate vs. Distance and
Supply Voltage.