SDCFX3-12288-388-J SanDisk, SDCFX3-12288-388-J Datasheet - Page 7
SDCFX3-12288-388-J
Manufacturer Part Number
SDCFX3-12288-388-J
Description
COMPACT FLASH 12GB EXTREME III
Manufacturer
SanDisk
Datasheet
1.SDCFH-1024-388.pdf
(108 pages)
Specifications of SDCFX3-12288-388-J
Memory Size
12GB
Memory Type
CompactFLASH
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 7 of 108
- Download datasheet (9Mb)
Introduction
CHAPTER 1
1.1
General Description
SanDisk CompactFlash® Memory Card products provide high capacity solid-state flash
memory that electrically complies with the Personal Computer Memory Card International
Association ATA (PC Card ATA) standard. (In Japan, the applicable standards group is
JEIDA.) The CompactFlash Memory Card Series also supports a True IDE Mode that is
electrically compatible with an IDE disk drive. The original CF form factor card can be used in
any system that has a CF slot, and with a Type II PCMCIA adapter can be used in any system
that has a PCMCIA Type II or Type III socket.
CompactFlash Memory cards use SanDisk Flash memory, which was designed by SanDisk
specifically for use in mass storage applications. In addition to the mass storage-specific flash
memory chips, CompactFlash Memory cards include an on-card intelligent controller that
provides a high level interface to the host computer. This interface allows a host computer to
issue commands to the memory card to read or write blocks of memory. The host addresses the
card in 512 byte sectors. Each sector is protected by a powerful Error Correcting Code (ECC).
The on-card intelligent controller in the CompactFlash Memory Card manages interface
protocols, data storage and retrieval as well as ECC, defect handling and diagnostics, power
management and clock control. Once the card has been configured by the host, it appears to the
host as a standard ATA (IDE) disk drive. Additional ATA commands have been provided to
enhance system performance.
The host system can support as many cards as there are CompactFlash and PCMCIA Type II or
III card slots. The original form factor CompactFlash Memory cards require a PCMCIA Type
II Adapter to be used in a PCMCIA Type II or Type III socket.
Figure 1-1 SanDisk CompactFlash Card Block Diagram
SanDisk CompactFlash
Data In/Out
SanDisk
Host
Flash
Single Chip
Interface
Memory
Control
Controller
© 2007 SanDisk Corporation
1-1
Rev. 12.0, 02/07
Related parts for SDCFX3-12288-388-J
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC MDOC G4 2GB 69-FBGA
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC P3 256MB 48-TSOP
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC P3 256MB 48-TSOP
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC P3 256MB 48-TSOP
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC H1 8GB 115-FBGA
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC H3 1GB FBGA
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC H3 2GB FBGA
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC H3 8GB FBGA
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC INAND FLASH 2GB 169FBGA
Manufacturer:
SanDisk
Datasheet: