MT5LSDT1672AG-13ED1 Micron Technology Inc, MT5LSDT1672AG-13ED1 Datasheet
MT5LSDT1672AG-13ED1
Specifications of MT5LSDT1672AG-13ED1
Related parts for MT5LSDT1672AG-13ED1
MT5LSDT1672AG-13ED1 Summary of contents
Page 1
... PRODUCTS AND SPECIFICATIONS DISCUSSED HEREIN ARE SUBJECT TO CHANGE BY MICRON WITHOUT NOTICE. 32MB, 64MB, 128MB (x72, SR) MT5LSDT472A – 32MB MT5LSDT872A(I) – 64MB MT5LSDT1672A(I) – 128MB For the latest data sheet, please refer to the Micron site: www.micron.com/products/modules Figure 1: 168-Pin DIMM (MO-161) Standard 1.00in. (25.40mm) Options • Package 168-pin DIMM (standard) 168-pin DIMM (lead-free) • ...
Page 2
... MT5LSDT1672A(I)Y-133_ MT5LSDT1672AG-10E_ MT5LSDT1672AY-10E_ NOTE: The designators for component and PCB revision are the last two characters of each part number. Consult factory for current revision codes. Example: MT5LSDT1672AG-133B1. 32, 64, 128MB x 64 SDRAM DIMM SD5C4_8_16x72AG.fm - Rev. C 6/04 EN 32MB, 64MB, 128MB (x72, SR) MODULE DENSITY ...
Page 3
... CB0 42 CKO 63 NOTE: 1. Pin 126 is NC for 32MB and 64MB modules, or A12 for the 128MB module. Figure 2: Pin Locations (168-Pin DIMM) Front View U1 PIN 1 Back View PIN 168 32, 64, 128MB x 64 SDRAM DIMM SD5C4_8_16x72AG.fm - Rev. C 6/04 EN 32MB, 64MB, 128MB (x72, SR) ...
Page 4
Table 6: PIN Descriptions Pins may not correlate with symbols; refer to Pin Assignment tables on page 3 for more information PIN NUMBERS SYMBOL 27, 111, 115 RAS#, CAS#, WE#, 42, 79 CK0, CK2 128 CKE0 30, 45 S0#, S2# ...
Page 5
... Input/Output ECC check bits. Supply Power Supply: +3.3V ±0.3V. DD Supply Ground. SS – Do Not Use: These pins are not used on these modules, but are assigned pins on other modules in this product family. – Not Connected: These pins are not connected on these modules. 5 168-PIN SDRAM UDIMM DESCRIPTION Micron Technology, Inc., reserves the right to change products or specifications without notice. © ...
Page 6
... A0-A11(32MB/64MB) A0-A12(128MB) BA0-1 Note: 1. All resistor values are 10 unless otherwise specified. 2. Per industry standard, Micron modules use various component speed grades as referenced in the module part numbering guide at www.micron.com/numberguide. 32, 64, 128MB x 64 SDRAM DIMM SD5C4_8_16x72AG.fm - Rev. C 6/04 EN 32MB, 64MB, 128MB (x72, SR) ...
Page 7
... PRECHARGE cycles and provide seamless, high-speed, random access operation. These modules are designed to operate in 3.3V, low- power memory systems. An auto refresh mode is pro- vided, along with a power-saving, power-down mode. ...
Page 8
Mode register bits M0–M2 specify the burst length, M3 specifies the type of burst (sequential or inter- leaved), M4–M6 specify the CAS latency, M7 and M8 specify the operating mode, M9 specifies the write burst mode, and M10 and M11 ...
Page 9
... For a burst length of one, A0–Ai select the unique col- umn to be accessed, and mode register bit M3 is ignored for 32MB module for 64MB and 128MB modules 32, 64, 128MB x 64 SDRAM DIMM SD5C4_8_16x72AG.fm - Rev. C 6/04 EN 32MB, 64MB, 128MB (x72, SR) Figure 5: CAS Latency Diagram ...
Page 10
Operating Mode The normal operating mode is selected by setting M7 and M8 to zero; the other combinations of values for M7 and M8 are reserved for future use and/or test modes. The programmed burst length applies to both READ ...
Page 11
Commands Table 9, Commands and DQMB Operation Truth Table, provides a general reference of available com- mands. For a more detailed description of commands Table 9: Commands and DQMB Operation Truth Table CKE is HIGH for all commands shown except ...
Page 12
Absolute Maximum Ratings Stresses greater than those listed may cause perma- nent damage to the device. This is a stress rating only, and functional operation of the device at these or any other conditions above those indicated in the opera- ...
Page 13
Table 12: I Specifications and Conditions – 64MB DD Notes 11, 13; notes appear following the parameter tables; V PARAMETER/CONDITION OPERATING CURRENT: Active Mode; Burst = 2; READ WRITE (MIN) STANDBY ...
Page 14
Table 15: Electrical Characteristics and Recommended AC Operating Conditions Notes 11, 31; notes appear following the parameter tables CHARACTERISTICS PARAMETER Access time from CLK (pos. edge Address hold ...
Page 15
Table 16: AC Functional Characteristics Notes 11, 31; notes appear following the parameter tables PARAMETER READ/WRITE command to READ/WRITE command CKE to clock disable or power-down entry mode CKE to clock enable or power-down exit setup ...
Page 16
Notes 1. All voltages referenced This parameter is sampled MHz 25°C; pin under test biased at 1.4V dependent on output loading and cycle DD rates. Specified ...
Page 17
SPD Clock and Data Conventions Data states on the SDA line can change only during SCL LOW. SDA state changes during SCL HIGH are reserved for indicating start and stop conditions, as indicated in Figure 6, Data Validity, and Figure ...
Page 18
Table 17: EEPROM Device Select Code The most significant bit (b7) is sent first Memory Area Select Code (two arrays) Protection Register Select Code Table 18: EEPROM Operating Modes MODE RW BIT Current Address Read 1 Random Address Read 0 ...
Page 19
Table 19: Serial Presence-Detect EEPROM DC Operating Conditions All voltages referenced DDSPD PARAMETER/CONDITION SUPPLY VOLTAGE INPUT HIGH VOLTAGE: Logic 1; All inputs INPUT LOW VOLTAGE: Logic 0; All inputs OUTPUT LOW VOLTAGE 3mA ...
Page 20
Table 21: Serial Presence-Detect Matrix “1”/”0”: Serial Data, “driven to HIGH”/”driven to LOW.” BYTE DESCRIPTION 0 Number of Bytes Used By Micron 1 Total Number of Spd Memory Bytes 2 Memory Type 3 Number of Row Addresses 4 Number of ...
Page 21
Table 21: Serial Presence-Detect Matrix “1”/”0”: Serial Data, “driven to HIGH”/”driven to LOW.” BYTE DESCRIPTION 30 Minimum RAS# Pulse Width, (Note 1) 31 Module Rank Density 32 Command and Address Setup Time 33 Command and Address Hold Time 34 Data ...
Page 22
R (2X) U1 0.118 (3.00) (2X) 0.118 (3.00) TYP 0.250 (6.35) TYP 0.118 (3.00) TYP 2.625 (66.68) PIN 1 (PIN 85 ON BACKSIDE) NOTE: All dimensions in inches (millimeters) Data Sheet Designation Released (No Mark): This data sheet ...