MT8HTF3264HY-53EB3 Micron Technology Inc, MT8HTF3264HY-53EB3 Datasheet - Page 4
![MODULE DDR2 256MB 200SODIMM](/photos/7/83/78349/mfg_mt_sodimm_series_sml.jpg)
MT8HTF3264HY-53EB3
Manufacturer Part Number
MT8HTF3264HY-53EB3
Description
MODULE DDR2 256MB 200SODIMM
Manufacturer
Micron Technology Inc
Datasheet
1.MT8HTF12864HY-40EA3.pdf
(14 pages)
Specifications of MT8HTF3264HY-53EB3
Memory Type
DDR2 SDRAM
Memory Size
256MB
Speed
533MT/s
Package / Case
200-SODIMM
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Table 7:
PDF: 09005aef80eec96e/Source: 09005aef80eec946
HTF8C32_64_128x64HG.fm - Rev. E 6/08 EN
RAS#, CAS#,
DQS#[8:0]
DQS[8:0],
DQ[63:0]
Symbol
CK#[1:0]
DM[8:0]
BA[2:0]
A[15:0]
CK[1:0]
RESET#
SA[1:0]
V
ODT0
CKE0
WE#
V
SDA
DDSPD
V
S0#
SCL
V
NC
REF
DD
SS
Pin Descriptions
Supply Power supply: 1.8V ±0.1V. The component V
Supply SPD EEPROM power supply: +1.7V to +3.6V.
Supply Reference voltage: V
Supply Ground.
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Type
I/O
I/O
I/O
–
Description
Address inputs: Provide the row address for ACTIVE commands, and the column address and
auto precharge bit (A10) for READ/WRITE commands, to select one location out of the memory
array in the respective bank. A10 sampled during a PRECHARGE command determines whether
the PRECHARGE applies to one device bank (A10 LOW, device bank selected by BA[2/1:0]) or all
device banks (A10 HIGH). The address inputs also provide the op-code during a LOAD MODE
command. A[12:0] (512MB) and A[13:0] (1GB, 2GB).
A[15:14] are connected for parity.
Bank address inputs: BA[2/1:0] define the device bank to which an ACTIVE, READ, WRITE, or
PRECHARGE command is being applied. BA[2/1:0] define which mode register (MR, EMR1,
EMR2, and EMR3) is loaded during the LOAD MODE command. BA[1:0] (512MB, 1GB) and
BA[2:0] (2GB).
Clock: CK and CK# are differential clock inputs. All control, command, and address input
signals are sampled on the crossing of the positive edge of CK and the negative edge of CK#.
Output data (DQ, DQS, and DQS#) is referenced to the crossings of CK and CK#.
Clock enable: CKE enables (registered HIGH) and disables (registered LOW) internal circuitry
and clocks on the DDR2 SDRAM.
Input data mask: DM is an input mask signal for write data. Input data is masked when DM is
sampled HIGH, along with the input data, during a write access. DM is sampled on both edges
of DQS. Although the DM pins are input-only, DM loading is designed to match that of the DQ
and DQS pins.
On-die termination: ODT enables (registered HIGH) and disables (registered LOW)
termination resistance internal to the DDR2 SDRAM. When enabled in normal operation, ODT
is only applied to the following pins: DQ, DQS, DQS#, DM, and CB. The ODT input will be
ignored if disabled via the LOAD MODE command.
Command inputs: RAS#, CAS#, and WE# (along with S#) define the command being entered.
Reset: Asynchronously forces all registered outputs LOW when RESET# is LOW. This signal can
be used during power-up to ensure that CKE is LOW and DQ are High-Z.
Chip select: S# enables (registered LOW) and disables (registered HIGH) the command
decoder.
Serial address inputs: These pins are used to configure the SPD EEPROM address range on
the I
Serial clock for SPD EEPROM: SCL is used to synchronize communication to and from the
SPD EEPROM.
Data input/output: Bidirectional data bus.
Data strobe: DQS# is only used when differential data strobe mode is enabled via the LOAD
MODE command. Output with read data. Edge-aligned with read data. Input with write data.
Center-aligned with write data.
Serial data: SDA is a bidirectional pin used to transfer addresses and data into and out of the
SPD EEPROM on the module on the I
No connect: These pins are not connected on the module.
2
C bus.
256MB, 512MB, 1GB: (x64, SR) 200-Pin DDR2 SDRAM SODIMM
DD
/2.
4
Module Pin Assignments and Descriptions
2
C bus.
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD
are connected to the module V
©2004 Micron Technology, Inc. All rights reserved.
DD
.