MT9VDDF3272G-26AC1 Micron Technology Inc, MT9VDDF3272G-26AC1 Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
MT9VDDF3272G-26AC1
Manufacturer Part Number
MT9VDDF3272G-26AC1
Description
MODULE SDRAM DDR 256MB 184DIMM
Manufacturer
Micron Technology Inc
Datasheet
1.MT9VDDF6472Y-335F1.pdf
(34 pages)
Specifications of MT9VDDF3272G-26AC1
Memory Type
DDR SDRAM
Memory Size
256MB
Speed
266MT/s
Package / Case
184-DIMM
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
progress, and the controller must wait the specified
time before initiating the subsequent operation. Vio-
lating either of these requirements will result in
unspecified operation.
A3 specifies the type of burst (sequential or inter-
leaved), A4–A6 specify the CAS latency, and A7–A12
specify the operating mode.
Burst Length
burst oriented, with the burst length being program-
mable, as shown in Figure 6, Mode Register Definition
Diagram. The burst length determines the maximum
number of column locations that can be accessed for a
given READ or WRITE command. Burst lengths of 2, 4,
or 8 locations are available for both the sequential and
the interleaved burst types.
operation or incompatibility with future versions may
result.
of columns equal to the burst length is effectively
selected. All accesses for that burst take place within
this block, meaning that the burst will wrap within the
block if a boundary is reached. The block is uniquely
selected by A1–Ai when the burst length is set to two,
by A2–Ai when the burst length is set to four and by
A3–Ai when the burst length is set to eight (where Ai is
the most significant column address bit for a given
configuration. See Note 5 of Table 6, Burst Definition
Table, on page 11, for Ai values). The remaining (least
significant) address bit(s) is (are) used to select the
starting location within the block. The programmed
burst length applies to both READ and WRITE bursts.
Burst Type
to be either sequential or interleaved; this is referred to
as the burst type and is selected via bit M3.
mined by the burst length, the burst type and the start-
ing column address, as shown in Table 6, Burst
Definition Table, on page 11.
pdf: 09005aef80e119b2, source: 09005aef807d56a1
DDF9C32_64x72G.fm - Rev. B 9/04 EN
Mode register bits A0–A2 specify the burst length,
Read and write accesses to DDR SDRAM devices are
Reserved states should not be used, as unknown
When a READ or WRITE command is issued, a block
Accesses within a given burst may be programmed
The ordering of accesses within a burst is deter-
10
Read Latency
between the registration of a READ command and the
availability of the first bit of output data. The latency
can be set to 2 or 2.5 clocks, as shown in Figure 7, CAS
Latency Diagram.
and the latency is m clocks, the data will be available
nominally coincident with clock edge n + m. Table 7,
CAS Latency Table, indicates the operating frequencies
at which each CAS latency setting can be used.
operation or incompatibility with future versions may
result.
* M14 and M13 (BA1 and BA0)
must be “0, 0” to select the
base mode register (vs. the
extended mode register).
The READ latency is the delay, in clock cycles,
If a READ command is registered at clock edge n,
Reserved states should not be used as unknown
Figure 6: Mode Register Definition
0*
14
BA1
256MB, 512MB (x72, ECC, SR)
Micron Technology, Inc., reserves the right to change products or specifications without notice.
0*
13
BA0
184-PIN DDR SDRAM RDIMM
12
A12 A11
Operating Mode
11
10
A10
M12 M11
0
0
-
9
A9
0
0
-
8
A8
M10
0
0
-
7
Diagram
A7 A6 A5 A4 A3
M9
M6
0
0
-
CAS Latency BT
0
0
0
0
1
1
1
1
6
M8 M7
0
1
M5
-
0
0
1
1
0
0
1
1
5
0
0
-
M4
0
1
0
1
0
1
0
1
4
©2004 Micron Technology, Inc. All rights reserved.
M3
M6-M0
0
1
Valid
Valid
3
-
Burst Length
M2
2
0
0
0
0
1
1
1
1
CAS Latency
A2 A1 A0
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
M1
0
0
1
1
0
0
1
1
Operating Mode
Normal Operation
Normal Operation/Reset DLL
All other states reserved
1
2.5
2
M0
0
1
0
1
0
1
0
1
0
Interleaved
Burst Type
Sequential
Reserved
Reserved
Reserved
Reserved
Reserved
Mode Register (Mx)
M3 = 0
Address Bus
2
4
8
Burst Length
Reserved
Reserved
Reserved
Reserved
Reserved
M3 = 1
2
4
8