MDLS-40263-C-HT-HV-FSTN-LED3G Varitronix, MDLS-40263-C-HT-HV-FSTN-LED3G Datasheet - Page 21

• Manufacturer Part Number: MDLS-40263-C-HT-HV-FSTN-LED3G
• Description: LCD MOD 40X2 CHAR FSTN GN BKLT
• Manufacturer: Varitronix
• Series: MDL(S)-40263r

Specifications of MDLS-40263-C-HT-HV-FSTN-LED3G

• Display Type: TN - Twisted Nematic
• Display Mode: Transflective
• Number Of Digits/alpha: 16
• Outline L X W X H: 108.00mm x 20.00mm x 12.00mm
• Viewing Area: 89.00mm L x 10.00mm W
• Backlight: LED - Green
• Display Format: 40 x 2
• Character Size: 3.15mm H x 1.85mm W
• Character Format: 5 x 8 Dots
• Voltage - Supply: 5.0V
• Dot Size: 0.33mm W x 0.35mm H
• Interface: Parallel
• Operating Temperature: -20°C ~ 70°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 153-1129

Mechanical
Damaget
Ink printing
defect
Category
Defect
Chip on ledge with
Chip on ledge with
ITO side (for Non
pin & COG model)
Chip on ledge
without ITO side
(for pin & COG
model)
Chip on ledge
without ITO side
(for Non pin &
COG model
Chip on end seal
Crack
Ink misalignment
Thick or thin ink.
Ink line/pattern are
thicker or thinner
than that specified
in the drawing
ITO side (for pin &
COG model)
The position of the
ink shift.
Defect Description
F
F
F
F
H
A, B, C,
D, E, F, G,
H
A, B, C,
D, E, F, G,
H
A, B, C
Zone
1-X ≦ 1/2 width of single ITO
2-Y <1/10 length of ledge
3- Z <1/10 glass thickness。
Whichever out of spec is not accept.
When Z <1/2 glass thickness:
1- X≦3mm;
When Z ≧1/2 glass thickness:
1- X≦2mm;
ledge/4.
Note﹕If glass thickness <0.7mm , accept
When Z <1/2 glass thickness:
1- X≦5mm;
2- Y≦1/4 length of ledge.
When Z≧1/2 glass thickness:
1- X≦2mm;
2- Y≦1/4 length of ledge/4.
Note﹕If glass thickness <0.7mm ,
When Z <3/4 glass thickness:
1- X≦5mm;
2- Y≦1/4 length of ledge.
When Z ≧3/4 glass thickness:
1- X≦2mm;
2- Y≦1/4 length of ledge/4.
Note﹕If glass thickness <0.7mm ,
Any chip can not be accept
Inspector shall attempt to remove the chip
with tweezers. Re-evaluate if the remaining
defect is still a crack or a chip. Reject chip
or crack of any size in EVA.
Accept if the shift is within the tolerance
and dimension specified in drawing.
Unless otherwise specified, tolerance of ink
printing shift should be ±0.5mm
(a) Accept if thick or thin part is less than
(b) Reject if thick or thin part is more than
Thick part outside EVA can be removed with
blade and the one inside EVA is not
acceptable.
10% or ≦0.15mm.
10% or ≧0.15mm
Z=glass thickness
accept Z=glass thickness
accept Z=glass thickness
2- Y≦1/4 length of ledge.
2- Y≦1/4 length of
Criterion
VL-FS-MDLS40263-01 REV.C
(MDLS40263-HT-HV-F-LED03-YG-12-CON)
PAGE 21 OF 25
JUN/2006
This drawing only for with ITO
Drawing Specification
side