MK-AOB3202405T Amulet Technologies LLC, MK-AOB3202405T Datasheet - Page 7

• Manufacturer Part Number: MK-AOB3202405T
• Description: MODULE 5.7" ONBOARD POS TRANSFLC
• Manufacturer: Amulet Technologies LLC

Specifications of MK-AOB3202405T

• Display Type: FSTN - Film Super-Twisted Nematic
• Display Mode: Transflective
• Viewing Area: 122.00mm L x 92.00mm W
• Backlight: LED - White
• Dot Size: 0.34mm W x 0.34mm H
• Dot Pitch: 0.36mm x 0.36mm
• Dot Pixels: 320 x 240 (QVGA)
• Description/function: On-Board Module
• Data Rate: 9.6 Kbps to 115.2 Kbps
• Operating Voltage: 5 V
• Pixel Format: 320 x 240
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 681-1014 - PEN STYLUS681-1012 - KIT BEZEL FOR MK-AOB3202405X681-1009 - BOARD INTERFACE ONBOARD RS232681-1008 - POWER SUPPLY 5V FOR ONBOARD MOD681-1007 - BOARD PROGRAM INTERFACE
• Interface: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 681-1005

6. Interface Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Pin #
Pin Type
I =
O =
P = Power Supply
1
PROG MODE
The I/O pins are only V
Section 4 (Absolute Maximum Ratings & Electrical Characteristics).
RAMTSTO
/RESET
Signal
FFBS
SCLK
MISO
MOSI
/CSS
GND
GND
/FSS
/TSS
GND
/BSS
GND
GND
GND
GND
GND
GND
GND
RXD
/SS4
/SS5
/SS6
1
1
TXD
TPC
/IRQ
V
V
CMOS Input
CMOS Output
CC
CC
Type Description
O
O
O
O
O
O
O
O
O
O
O
P
P
P
P
P
P
P
P
P
P
P
P
I
I
I
I
I
I
I
Ground.
Ground.
1
1
1
1,6
1
Ground.
1
1,2,6
level boots Amulet in program mode.
1
1,4,6
session. A high level performs a calibration session.
1
1,3,6
to 19,200 bps. A high level sets the flash programming rate to 115,200 bps.
1
Ground.
1
1,6,7
Ground.
1,6
1
Ground.
1,6
Ground.
1
Ground.
Ground.
5
should be applied to this pin.
Ground.
5
Flash slave select. This pin should be left unconnected.
Asynchronous data output.
Touch panel slave select. This pin should be left unconnected.
Contrast slave select. This pin should be left unconnected.
Backlight slave select. This pin should be left unconnected.
SPI slave select 4. This pin is for future use and should be left unconnected.
SPI slave select 5. This pin is for future use and should be left unconnected.
SPI slave select 6. This pin is for future use and should be left unconnected.
External SRAM test results. This pin should be left unconnected.
SPI clock. This pin should be left unconnected.
SPI data out. This pin should be left unconnected.
Supply voltage for module. A regulated voltage between 4.75V and 5.25V
Supply voltage for module. A regulated voltage between 4.75V and 5.25V
Asynchronous data input.
System interrupt. This pin should be left unconnected.
SPI data in. This pin should be left unconnected.
System power up mode. A low level boots Amulet in run mode. A high
Touch panel calibration mode. A low level does not perform a calibration
Flash programming baud rate. A low level sets the flash programming rate
System reset. A low level of 10us or longer will generate a system reset.
DD
tolerant and must adhere to the voltage levels depicted in
7