LQ104V1DG51 Sharp Microelectronics, LQ104V1DG51 Datasheet - Page 8
![LCD TFT 10.4" 640X480 VGA](/photos/15/66/156629/822007135459_sml.jpg)
LQ104V1DG51
Manufacturer Part Number
LQ104V1DG51
Description
LCD TFT 10.4" 640X480 VGA
Manufacturer
Sharp Microelectronics
Datasheet
1.LQ104V1DG51.pdf
(22 pages)
Specifications of LQ104V1DG51
Display Type
LCD - Color
Display Mode
*
Viewing Area
211.20mm L x 158.40mm W
Dot Pixels
640 x 480 (VGA)
Pixel Density
640 x 480
Module Size (w X H X T)
246.5 mm x 179.4 mm x 15.5 mm
Backlighting
White Normally White
Diagonal
10.4 in
Viewing Area (w X H)
211.2 mm x 158.4 mm
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Interface
-
Backlight
-
Dot Size
-
Dot Pitch
-
Lead Free Status / Rohs Status
Details
Other names
425-2470
6-2. Backlight driving
Lamp life time
[Note1] Lamp current is measured with current meter for high frequency as shown below.
[Note2] Referential data per one CCFT by calculation. (I L
[Note3] Lamp frequency may produce interference with horizontal synchronous frequency,and this may cause
[Note4] The open output voltage of the inverter shall be maintained for more than 1s; otherwise
[Note5] Above value is applicable when lamp (the long side of LCD module) is placed horizontally.
[Note6] The performance of the backlight, for example life time or brightness, is much influenced
[Note7] It is required to have the inverter designed so that to allow the impedance deviation of the two CCFT
[Note8] Under the environment of 10lx or less, miss-lighting delay may occur.
Lamp current
Lamp power consumption
Lamp frequency
Kick-off voltage
Module
The data don’t include loss at inverter. ( IL=6.0mArms)
the lamp may not be turned on.
Lamp life time is defined that it applied either
(Lamp lifetime may vary if lamp is in portrait position due to the change of mercury density inside the
In case of operating under lower temp environment, the lamp exhaustion is accelerated
lamps and the capacity deviation of barast capacitor.
beat on the display. Therefore lamp frequency shall be detached as much as possible from the horizontal
synchronous frequency and from the harmonics of horizontal synchronous to avoid interference.
(Landscape position)
The backlight system is an edge-lighting type with double CCFT (Cold Cathode
Parameter
lamp.)
and the brightness becomes lower.
(Continuous operating for around 1 month under lower temp condition may reduce the
In case of such usage under lower temp environment, periodical lamp exchange is recommended.
by the characteristics of the DC-AC inverter for the lamp. When you design or order the
inverter, please make sure that a poor lighting caused by the mismatch of the backlight and
the inverter (miss-lighting,flicker, etc.) never occur. when you confirm it, the module should
be operated in the same condition as it is installed in your instrument.
Be sure to use a back light power supply with the safety protection circuit such as the detection circuit
for the excess voltage, excess current and or electric discharge waveform.
Be sure to use the detect circuit by which one side of the CCFT lamps can be controlled
independently. Otherwise, when one side of the CCFT is open, the excess current may possibly
be applied to the other side of the lamp.
Fluorescent Tube). The characteristics of lamp are shown in the following table.
(Continuous turning on at Ta=25
brightness to half of the original brightness.)
(It is usually required to measure under the following condition.
condition:IL=6.0mA,Ta=25
Brightness becomes 50% of the original value under standard condition.
Kick-off voltage at Ta=-10
CN2: 1pin
CN2: 3pin
Symbol
Vs
P
F
L
I
L
L
L
L
50000
30000
o
Min.
C exceeds maximum value,1500Vrms.
3.5
40
o
C, IL=6.0mA rms)
2 ,FL=60kHz.)
Typ.
6.0
2.8
60
Inverter
output voltage
or
Max.
1000
1300
1450
VL)
7.0
70
under this condition
mArms
Vrms Ta=25
Vrms Ta =0
Vrms Ta =-10
KHz
hour
hour
Unit
Note1
Note2
Note3
Note5
Note5
Transformer
output voltage
Inverter
Remark
Note4
Note4
Note4