HFBR-5912EZ Avago Technologies US Inc., HFBR-5912EZ Datasheet
HFBR-5912EZ
Specifications of HFBR-5912EZ
Available stocks
Related parts for HFBR-5912EZ
HFBR-5912EZ Summary of contents
Page 1
... Vertical Cavity Surface Emitting Laser (VCSEL optical subassembly (OSA), which mates to the fiber cable. Receiver Section The receiver of the HFBR-5912EZ includes a GaAs PIN photodiode mounted together with a custom, silicon bipolar transimpedance preamplifier OSA. This OSA is mated to a custom silicon bipolar circuit that provides post- amplification and quantization ...
Page 2
... Recommended Solder fluxes Solder fluxes used with the HFBR-5912EZ should be water-soluble, organic fluxes. Recommended solder fluxes include Lonco 3355-11 from London Chemical West, Inc. of Burbank, CA, and 100 Flux from Alpha-Metals of Jersey City, NJ ...
Page 3
... HFBR-5912EZ. All adjustments are made at the factory before shipment to our customers. Tampering with or modifying the performance of the HFBR-5912EZ will result in voided product warranty. It may also result in improper operation of the HFBR-5912EZ circuitry, and possible overstress of the laser source. Device degradation or product failure may result ...
Page 4
... Gigabit data communication systems. To minimize the impact of conducted and radiated noise upon receiver performance the metal cover at the rear of the HFBR-5912EZ should be connected to the host system’s circuit common ground plane. To maximize the shielding effectiveness and minimize the radiated emissions that escape from the host system’ ...
Page 5
... In the HFBR-5912EZ there are three key elements to the laser driver safety circuitry: a monitor diode, a window detector circuit, and direct control of the laser bias. The window detection circuit monitors the average optical power using the monitor diode ...
Page 6
Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause catastrophic damage to the device. Limits apply to each parameter in isolation, all other parameters having values within the recommended operating conditions. It should not be assumed ...
Page 7
... HFBR-5912EZ, 850 nm VCSEL Transmitter Electrical Characteristics (T = 0°C to +70° Parameter Supply Current Power Dissipation Receiver Electrical Characteristics (T = 0°C to +70° Parameter Supply Current Power Dissipation Data Output Voltage - Low Data Output Voltage - High Data Output Rise Time ...
Page 8
... HFBR-5912EZ Family, 850 nm VCSEL Transmitter Optical Characteristics (T = 0°C to +70° Parameter Output Optical Power 50/125 µ 0.20 Fiber Output Optical Power 62.5/125 µ 0.275 Fiber Disabled Transmit Output Power Optical Extinction Ratio Center Wavelength Spectral Width - rms Optical Rise/Fall Time ...
Page 9
Grounding Tabs RECEIVER SIGNAL GROUND RECEIVER POWER SUPPLY SIGNAL DETECT RECEIVER DATA OUT BAR RECEIVER DATA OUT Figure 2. Pin Out Table 1. Pin Out Table Pin Symbol Two Mounting Studs The mounting studs are provided for transceiver mechanical attachment ...
Page 10
... VENDORS' MODULES. THE HFBR-5912EZ WILL OPERATE IN BOTH CONFIGURATIONS. ** RECOMMENDED BYPASS CAPACITOR FOR ADDITIONAL LOW FREQUENCY NOISE FILTERING. THE SIGNAL DETECT OUTPUT ON THE HFBR-5912EZ CONTAINS AN INTERNAL 1.8 k PULL UP RESISTOR. Figure 3. Recommended Gigabit/sec Ethernet HFBR-5912EZ Fiber-Optic Transceiver and HDMP-1636A/1646A SERDES Integrated Circuit Transceiver Interface and Power Supply Filter Circuits. ...
Page 11
... THE 10 I/O PINS, 2 SOLDER POSTS AND 4 PACKAGE GROUNDING TABS ARE TO BE TREATED AS A SINGLE PATTERN. (SEE FIGURE 5 PCB LAYOUT). 4. THE MT-RJ HAS A 750 µm FIBER SPACING. 5. THE MT-RJ ALIGNMENT PINS ARE IN THE MODULE. 6. SEE MT-RJ TRANSCEIVER PIN OUT DIAGRAM FOR DETAILS. Figure 4. Package Outline Drawing of HFBR-5912EZ 11 13.97 (0.55) MIN. ...
Page 12
DIMENSIONS IN MILLIMETERS (INCHES) NOTES: 1. THIS FIGURE DESCRIBES THE RECOMMENDED CIRCUIT BOARD LAYOUT FOR THE MT-RJ TRANSCEIVER PLACED ...
Page 13
... Ordering Information HFBR-5912EZ - 850 nm VCSEL (Short Wavelength Laser) 1000 Base SX Application For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Pte. in the United States and other countries. Data subject to change. Copyright © 2006 Avago Technologies Pte. All rights reserved. ...