LTL-4251N Lite-On Electronics, LTL-4251N Datasheet
LTL-4251N
Specifications of LTL-4251N
LT1145
Available stocks
Related parts for LTL-4251N
LTL-4251N Summary of contents
Page 1
... All dimensions are in millimeters (inches). 2. Tolerance is ± 0.25mm(.010") unless otherwise noted. 3. Protruded resin under flange is 1.0mm(.04") max. 4. Lead spacing is measured where the leads emerge from the package. 5. Specifications are subject to change without notice. Part No. : LTL-4251N BNS-OD-C131/ Lens Yellow Diffused ...
Page 2
... Duty Cycle, 0.1ms Pulse Width) DC Forward Current Derating Linear From 50 ℃ Reverse Voltage Operating Temperature Range Storage Temperature Range Lead Soldering Temperature [2.0mm(.078") From Body] Part No. : LTL-4251N BNS-OD-C131/ =25 ℃ ℃ ℃ ℃ A Maximum Rating 0.25 -55 ℃ 100 ℃ -55 ℃ 100 ℃ ...
Page 3
... The dominant wavelength, λ wavelength which defines the color of the device. 4. The Iv guarantee should be added ± 15% . Part No. : LTL-4251N BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION =25 ℃ ℃ ℃ ℃ A Symbol Min ...
Page 4
... Typical Electrical / Optical Characteristics Curves (25 ℃ Ambient Temperature Unless Otherwise Noted) Part No. : LTL-4251N BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Page : ...
Page 5
... Inner cartons per outer carton total 80000 pcs per outer carton In every shipping lot, only the last pack will be non-full packing Part No. : LTL-4251N BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Packing Spec Page : ...
Page 6
... Bin Code 1 J1 J2A J2B J3 Note: Tolerance of each bin limit is ±15% Dominant Wavelength Bin Code Note: Tolerance of each bin limit is ±1nm Part No. : LTL-4251N BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Unit : mcd @10mA Min. 14.5 8.74 7.4 5.6 3.7 Unit : nm @10mA Min. 592 589 ...
Page 7
... Max. (one time only) Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or catastrophic failure of the LED. IR reflow is not suitable process for through hole type LED lamp product. Part No. : LTL-4251N BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION CAUTIONS Wave soldering ...
Page 8
... To verify for ESD damage, check for “light up” and Vf of the suspect LEDs at low currents. The Vf of “good” LEDs should be >2.0V@0.1mA for InGaN product and >1.4V@0.1mA for AlInGaP product. Part No. : LTL-4251N BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION ...
Page 9
... No static charge generators (e.g. plastics) inside shielding containers with ESDS items? 4. All flexible conductive and dissipative package materials inspected before reuse or recycle? Others 1. Audit result reported to entity ESD control coordinator? 2. Corrective action from previous audits completed? 3. Are audit records complete and on file? Part No. : LTL-4251N BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Page : 9 of ...