HLMP-1503-C00A1 Avago Technologies US Inc., HLMP-1503-C00A1 Datasheet - Page 13

• Manufacturer Part Number: HLMP-1503-C00A1
• Description: LED 3MM GAP DIFF GRN RA HOUSING
• Manufacturer: Avago Technologies US Inc.
• Type: Uni-Colorr

Specifications of HLMP-1503-C00A1

• Viewing Angle: 60°
• Color: Green
• Voltage Rating: 2.1V
• Current: 10mA
• Lens Type: Diffused, Green Tinted
• Lens Style/size: Round, 3mm, T-1
• Configuration: Single
• Mounting Type: Through Hole
• Package / Case: Radial - 2 Lead
• Voltage - Forward (vf) Typ: 2.1V
• Millicandela Rating: 2.6mcd
• Luminous Flux @ Current - Test: 2 mlm
• Current - Test: 10mA
• Wavelength - Peak: 565nm
• Resistance Tolerance: 569nm
• Bulb Size: T-1 (3mm)
• Led Color: Green
• Luminous Intensity: 2.6mcd
• Forward Current If: 10mA
• Forward Voltage: 2.1V
• Led Mounting: Through Hole
• Lens Shape: Round
• Wavelength Typ: 569nm
• Package Type: T-1
• Emitting Color: Yellow Green
• Test Current (it): 10mA
• Forward Current: 30mA
• Dominant Wave Length: 569nm
• Product Length (mm): 3.43mm
• Product Height (mm): 4.7mm
• Product Depth (mm): 3.43mm
• Mounting: Through Hole
• Peak Wavelength: 565nm
• Shape Type: Circular
• Chip Material: GaP
• Main Category: Standard LED
• Number Of Elements: 1
• Pin Count: 2
• Operating Temperature Classification: Commercial
• Operating Temp Range: -20C to 100C
• Reverse Voltage: 5V
• Lens Dimensions: 3.18x3.18x3.68mm
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Not applicable / Not applicable
• Other names: 516-1753; HLMP-1503-C00A1

Precautions
Lead Forming
• The leads of an LED lamp may be preformed or cut to
• If lead forming is required before soldering, care must
• It is recommended that tooling made to precisely form
Soldering Conditions
• Care must be taken during PCB assembly and soldering
• The closest LED is allowed to solder on board is 1.59
• Recommended soldering conditions:
Figure 17. Recommended wave soldering profile.
For product information and a complete list of distributors, please go to our web site:
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2008 Avago Technologies. All rights reserved. Obsoletes 5989-4252EN
AV02-1555EN - October 13, 2008
length prior to insertion and soldering into PC board.
be taken to avoid any excessive mechanical stress
induced to LED package. Otherwise, cut the leads of LED
to length after soldering process at room temperature.
The solder joint formed will absorb the mechanical
stress of the lead cutting from traveling to the LED chip
die attach and wirebond.
and cut the leads to length rather than rely upon hand
operation.
process to prevent damage to LED component.
mm below the body (encapsulant epoxy) for those
parts without standoff.
Pre-heat Temperature 105 °C Max.
Pre-heat Time
Peak Temperature
Dwell Time
250
200
150
100
50
30
0
10
FLUXING
20
PREHEAT
TURBULENT WAVE
30
Wave Soldering
30 sec Max.
50 °C Max.
3 sec Max.
40
TIME – SECONDS
50
60
70
LAMINAR WAVE
Manual Solder
Dipping
–
–
60 °C Max.
5 sec Max.
HOT AIR KNIFE
80
90
100
www.avagotech.com
• Wave soldering parameter must be set and maintained
• If necessary, use fixture to hold the LED component
• Proper handling is imperative to avoid excessive
• Special attention must be given to board fabrication,
• Recommended PC board plated through hole sizes for
Note:
Refer to application note AN107 for more information on
soldering LED components.
CONVEYOR SPEED = 1.83 M/MIN (6 FT/MIN)
PREHEAT SETTING = 150C (100C PCB)
SOLDER WAVE TEMPERATURE = 245C
AIR KNIFE AIR TEMPERATURE = 390C
AIR KNIFE DISTANCE = 1.91 mm (0.25 IN.)
AIR KNIFE ANGLE = 40
SOLDER: SN63; FLUX: RMA
NOTE: ALLOW FOR BOARDS TO BE
SUFFICIENTLY COOLED BEFORE EXERTING
MECHANICAL FORCE.
according to recommended temperature and dwell
time in the solder wave. Customer is advised to
periodically check on the soldering profile to ensure
the soldering profile used is always conforming to
recommended soldering condition.
in proper orientation with respect to the PCB during
soldering process.
thermal stresses to LED components when heated.
Therefore, the soldered PCB must be allowed to cool to
room temperature, 5°C, before handling.
solder masking, surface plating and lead holes size and
component orientation to assure solderability.
LED component leads:
LED Component
Lead Size
0.457 x 0.457 mm
(0.018 x 0.018 inch)
0.508 x 0.508 mm
(0.00x 0.00 inch)
BOTTOM SIDE
OF PC BOARD
TOP SIDE OF
PC BOARD
Diagonal
0.646 mm
(0.05 inch)
0.718 mm
(0.08 inch)
Plated Through
Hole Diameter
0.976 to 1.078 mm
(0.038 to 0.04 inch)
1.049 to 1.150 mm
(0.041 to 0.045 inch)