LTL2T3TBK5 Lite-On Electronics, LTL2T3TBK5 Datasheet - Page 3

• Manufacturer Part Number: LTL2T3TBK5
• Description: LED 5MM 468NM BLUE WATER CLEAR
• Manufacturer: Lite-On Electronics

Specifications of LTL2T3TBK5

• Led Size: T-1 3/4
• Illumination Color: Blue
• Lens Color/style: Water Clear
• Operating Voltage: 3.5 V
• Wavelength: 470 nm
• Luminous Intensity: 1200 mcd
• Operating Current: 20 mA
• Lens Dimensions: 5 mm
• Lens Shape: Dome
• Maximum Operating Temperature: + 80 C
• Minimum Operating Temperature: - 25 C
• Mounting Style: Through Hole
• Viewing Angle: 30°
• Package / Case: Radial - 2 Lead
• Color: Blue
• Millicandela Rating: 880mcd
• Current - Test: 20mA
• Wavelength - Dominant: 470nm
• Wavelength - Peak: 468nm
• Voltage - Forward (vf) Typ: 3.5V
• Lens Type: Clear
• Lens Style/size: Round, 5mm, T-1 3/4
• Height: 8.70mm
• Mounting Type: Through Hole
• Resistance Tolerance: 470nm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Luminous Flux @ Current - Test: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 160-1610

NOTE: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE
BNS-OD-C131/A4
Part No. : LTL2T3TBK5
Electrical / Optical Characteristics at T
Luminous Intensity
Viewing Angle
Peak Emission Wavelength
Dominant Wavelength
Spectral Line Half-Width
Forward Voltage
Reverse Current
2. θ
3. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single
4. Iv classification code is marked on each packing bag.
5. The Iv guarantee should be added ±15% tolerance.
6. Precautions in handling:
7. Caution in ESD:
eye-response curve.
wavelength which defines the color of the device.
Static Electricity and surge damages the LED. It is recommend to use a wrist band or anti-electrostatic
glove when handling the LED. All devices, equipment and machinery must be properly grounded.
‧ When soldering, leave 2mm of minimum clearance from the resin to the soldering point.
‧ Dipping the resin to solder must be avoided.
‧ Correcting the soldered position after soldering must be avoided.
‧ In soldering, do not apply any stress to the lead frame particularly when heated.
‧ When forming a lead, make sure not to apply any stress inside the resin.
‧ Lead forming must be done before soldering.
‧ It is necessary to cut the lead frame at normal temperature.
1/2
Parameter
is the off-axis angle at which the luminous intensity is half the axial luminous intensity.
LITE-ON TECHNOLOGY CORPORATION
Symbol
2θ
∆λ
V
λ
λ
I
I
V
R
1/2
P
d
F
P r o p e r t y o f L i t e - O n O n l y
Min.
520
A
=25ºC
1200
Typ.
468
470
3.5
30
25
Max.
100
3.8
Page : 3
Unit
mcd
deg
nm
nm
nm
µA
V
I
Note 1,5
Note 2 (Fig.6)
Measurement
@Peak (Fig.1)
Note 3
I
V
F
F
Test Condition
R
= 20mA
= 20mA
= 5V
of
10