NT-53F0-0428 LIGHTING SCIENCE GROUP CORPORATION, NT-53F0-0428 Datasheet - Page 26
![LIGHT ENGINE TITAN RED/GRN/BLUE](/photos/8/29/82976/nt-53f0-0428_sml.jpg)
NT-53F0-0428
Manufacturer Part Number
NT-53F0-0428
Description
LIGHT ENGINE TITAN RED/GRN/BLUE
Manufacturer
LIGHTING SCIENCE GROUP CORPORATION
Series
Titan™r
Type
With Connectorr
Specifications of NT-53F0-0428
Color
Red, Green, Blue (RGB)
Luminous Flux @ Current - Test
435 lm Red, 685 lm Green, 183 lm Blue
Current - Test
3 x 1.05A
Current - Max
3 x 1.4A
Driver Circuitry
No
Voltage
6.9V Red, 11.4V Green, 10.5V Blue
Configuration
Circular
With Connector
Yes
Voltage - Input
6.9V Red, 11.4V Green, 10.5V Blue
Power - Input
7.3W Red, 12W Green, 11W Blue
Product
LED Modules
Illumination Color
Red, Green, Blue
Power Consumption
9.9 W, 15.1 W, 16 W
Supply Voltage
8 V, 12.2 V, 12.9 V
Supply Current
1.4 A
Wavelength
629 nm, 535 nm, 470 nm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Interface
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
521-1045
©2008 L
a
tLas
tm
s
amina
eries
p
Lamina’s light engines may be covered by pending patents and/or one or more of the following U.S. and/or
International patents 5876536, 6709749 B, 595880, 6017642, 5565262, 5681444, 5653834, 5581876, 5847935,
5514451, 5747931, 5925203, 5725808, 5929510, 5858145, 5866240, 5953203, 6055151, 614076, 6011330,
6399230, 6914501, 6168490, 6191934, 614075, 6160469, 6300267, 6471805, 6518502, 6739047, 6720859,
6759940, 6518502, 6670856 B1, 6720859, 6713862 B2, WO 00/47399, WO 00/26152, WO 98/19339, 5082804,
ZL99808762.9, 69623930, 69628549, 69629572, 805785, 69628549, 843621, 932500, 805785, 812258,
843621, 932500, 805785, 812258, 843621, 932500, 805785, 812258, 843621, 932500, 3327556, 3267299,
3226281, 3405545, 320630, 295695, 284068, 546471, 805785, 812258, 843621, 6455930, 6759940, 6713862,
7095053, 7098483.
e
LED light engines are available with or without Lamina’s EZConnect board. EZConnect adapter boards have
AMP connectors for solderless connections to Lamina’s wiring harness.
As with many electrical devices, non-acid RMA type solder flux should be used to prepare the solder pads before
application of solder. Ensure proper strain relief of wires attached to the light engine to prevent damage to the
light engines solder pads. For more information refer to Lamina’s connection application note AN-05 which can
be found on the website at www.laminalighting.com.
Functional test: Parts may be tested using a constant current source set at 25% of Drive Current for no more
than two seconds without heat sink.
1.
2.
A
Lamina’s Series Light Engines are designed for attachment to a heat sink with conductive epoxy, or screw down
for flange mount devices with thermal grease in the joint. For attachment using screws, a 2-56 UNC round head
or metric equivalent M2 X 0.4 cheese head screw, 18-8 SS is recommended. When mounting the light engine,
position the three screws in the center of each of the three slots. Tighten the three screws evenly, first to about
0.89 inch pounds (10 Newton-centimeter), and then tighten each to a maximum torque of 4 inch pounds (45
Newton-centimeter). Flatness requirement of the surface that the light engine is mounted to is 0.001 inch/inch
(1mm/meter).
All specifications are based on mounting the LED array to a heat sink using the specified hardware and thermal
grease (e.g. Wakefield P/N 120). The heat sink must meet the specified flatness requirement. Mounting using
screws and thermal tape may damage the device.
r
Your parts will arrive in either custom fitted trays or on easy to use tape and reel packaging. This packaging
was designed to provide the necessary protection during shipment and to take up the least amount of space in
your storage area.
Notes
1.
2.
3.
4.
p
L
Led L
ighting
Atents
leCtriCAl
sseMbly
eCeiving
Atents
Optical and electrical specifications are given for the specified drive @ 25ºC junction temperature.
When using constant current LED drivers with high compliance voltage (Advance, LEDworks, etc. or a
custom driver) the output of the supply must be connected to the part before power is applied to the input
of the supply.
This product uses silicone materials for superior optical performance. Do not expose the part to fluids that
may react with silicone compounds. See Dow Chemical Form 45-0113D-01, Silicone Fluid Resistance
Guide.
Ray trace models are available upon request.
Lamina may make process or materials changes affecting the performance or other characteristics of our
products. These products supplied after such changes will continue to meet published specifications, but
may not be identical to product supplied as samples or under prior orders.
All specifications are based on mounting the LED array to a heat sink using the specified hardware and
thermal grease Wakefield P/N 120. The heat sink must meet the specified flatness requirement. Mounting
using screws and thermal tape may damage the device.
ight
i
ncorporated
e
ngines
r
p
, C
C
Fm-0167 r
eCoMMenDAtions
Arts AnD
onneCtions
onneCtions
ev
05.21.08
p
ACkAging
, A
t
sseMbly
rAys
,
AnD
p
ACkAging