FT63EP200 Copal Electronics Inc, FT63EP200 Datasheet - Page 2
![no-image](/images/no-image-200.jpg)
FT63EP200
Manufacturer Part Number
FT63EP200
Description
POT 20 OHM SINGLE CERMET TOP
Manufacturer
Copal Electronics Inc
Series
FT-63r
Datasheet
1.FT63EP100.pdf
(7 pages)
Specifications of FT63EP200
Resistance (ohms)
20
Power (watts)
0.5W, 1/2W
Taper
Linear
Tolerance
±10%
Temperature Coefficient
±150ppm/°C
Number Of Turns
Single
Adjustment Type
Top Adjustment
Mounting Type
Through Hole
Resistive Material
Cermet
Package / Case
Square - 0.276" L x 0.276" W x 0.228" H (7.00mm x 7.00mm x 5.80mm)
Resistance In Ohms
20.0
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
FT-63EP200
■
■
■ Specifications are subject to change without notice. Specifications in this catalog are for reference. The formal specification sheets will be submitted upon request.
Top adjustment
Side adjustment
Nominal resistance range
Resistance tolerance
Power ratings
Resistance law
Maximum input voltage
Maximum wiper current
Effective electrical angle
End resistance
C.R.V.
Operating temp. range
Temp. coefficient
Insulation resistance
Dielectric strength
Net weight
Adjustment position
:
LIST OF PART NUMBERS
ELECTRICAL CHARACTERISTICS
Not manufactured
Taping (Ammo pack type)
FT-63ETP
FT-63ETV
FT-63ETS
FT-63ETH
DC200 V or power rating, whichever is smaller
Approx. 0.52 g (FT-63EP, EV)
Approx. 0.66 g (FT-63ES, EH, EX, EN)
50
10
1 % or 2 , whichever is greater
2 % or 3 , whichever is greater
1000 M minimum (DC500 V)
0.5 W (70 °C) 0 W (125 °C)
~ 2 M : 100 10
~ 20
Form of packaging
AC900 V, 60 s
Power ratings
220 ° (1 turn)
10
: 150 10
Linear law
55 ~ 125 °C
10 %
~ 2 M
-6
-6
/°C maximum
/°C maximum
Plastic bag
FT-63EP
FT-63EV
FT-63ES
FT-63EX
FT-63EH
FT-63EN
〈
※ The above part numbers are all available with the respective combination of
※ Verify the above part numbers when placing orders.
※ Taping specification is not sold separately and must be purchased in taping unit.
The products indicated by A mark are manufactured upon receipt of
order basis.
■
Mechanical angle
Operating torque
Stop strength
Rotational life
Terminal strength
Thrust to rotor
Solderability
Nominal resistance values
A 10
<Nominal resistance values> (Fig. 1).
50 k
1 k
MECHANICAL CHARACTERISTICS
A 20
100 k
2 k
200 k
50
3 k
COPAL ELECTRONICS
300 k
100
100 cycles [ Δ R/R ≦
5 k
CERMET TRIMMERS
20 mN·m {204 gf·cm} maximum
50 mN·m {510 gf·cm} minimum
10 N {1.02 kgf} minimum
10 N {1.02 kgf} minimum
〉
(
245 3 °C, 2 ~ 3 s
500 k
Tensile strength
200
10 k
260 ° (1 turn)
300
20 k
1 M
{ }
FT-63
(2
:
)
Reference only
500
30 k
2 M
3 %)]
Fig. 1