BWR-12/725-D24A-C Murata Power Solutions Inc, BWR-12/725-D24A-C Datasheet - Page 4
![CONV DC/DC +/-12V +/-725MA DIP](/photos/8/59/85976/bwr-12_725-d24a-c__sml.jpg)
BWR-12/725-D24A-C
Manufacturer Part Number
BWR-12/725-D24A-C
Description
CONV DC/DC +/-12V +/-725MA DIP
Manufacturer
Murata Power Solutions Inc
Series
BWRr
Type
Isolatedr
Datasheet
1.BWR-12725-D48A-C.pdf
(9 pages)
Specifications of BWR-12/725-D24A-C
Number Of Outputs
2
Output
±12V
Power (watts)
17W
Mounting Type
Through Hole
Voltage - Input
18 ~ 36V
Package / Case
6-DIP Module
1st Output
12 VDC @ 725mA
2nd Output
-12 VDC @ 725mA
Size / Dimension
2.00" L x 1.00" W x 0.47" H (50.8mm x 25.4mm x 11.8mm)
Power (watts) - Rated
17W
Efficiency
85%
Approvals
CE, cUL, EN, UL
Output Power
9 W
Input Voltage Range
18 V to 36 V
Output Voltage (channel 1)
12 V
Output Current (channel 1)
0.725 A
Output Voltage (channel 2)
- 12 V
Output Current (channel 2)
-0.725 A
Isolation Voltage
1.5 KV
Product
Isolated
Dc / Dc Converter O/p Type
Dual
No. Of Outputs
2
Input Voltage
18V To 36V
Power Rating
17W
Output Voltage
12V
Output Current
725mA
Output Voltage 2
-12V
Output Current 2
-725mA
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
3rd Output
-
4th Output
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
811-1726-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
BWR-12/725-D24A-C
Manufacturer:
Murata Power Solutions Inc
Quantity:
312
Company:
Part Number:
BWR-12/725-D24A-C
Manufacturer:
DATEL
Quantity:
228
Input Fusing
Certain applications and/or safety agencies may require the installation of fuses
at the inputs of power conversion components. Fuses should also be used if
the possibility of sustained, non-current-limited, input-voltage polarity reversal
exists. For MPS BWR 15-17 Watt DC/DC Converters, you should use slow-blow
type fuses with values no greater than the following:
Start-Up Time
The V
crosses the turn-on threshold point, and the fully loaded output voltage enters
and remains within its specifi ed accuracy band. Actual measured times will vary
with external output capacitance and load. The BWR 15-17W Series implements
a soft start circuit that limits the duty cycle of the PWM controller at power up,
thereby limiting the Input Inrush current.
The On/Off Control to V
input voltage applied but is turned off via the On/Off Control pin. The specifi cation
defi nes the interval between the time at which the converter is turned on and the
fully loaded output voltage enters and remains within its specifi ed accuracy band.
Similar to the V
governed by the internal soft start circuitry and external load capacitance.
Input Overvoltage/Undervoltage Shutdown and Start-Up Threshold
Under normal start-up conditions, devices will not begin to regulate until the ramping-up
input voltage exceeds the Start-Up Threshold Voltage (35V for D48 models). Once
operating, devices will not turn off until the input voltage drops below the Undervoltage
Shutdown limit (33.5V for D48 models). Subsequent re-start will not occur until the input is
brought back up to the Start-Up Threshold. This built in hysteresis prevents any unstable
on/off situations from occurring at a single input voltage.
Input voltages exceeding the input overvoltage shutdown specifi cation listed in
the Performance/Functional Specifi cations will cause the device to shutdown. A
built-in hysteresis of 0.6 to 1.6 Volts for all models will not allow the converter to
restart until the input voltage is suffi ciently reduced.
Input Source Impedance
The converters must be driven from a low ac-impedance input source. The DC/
DC's performance and stability can be compromised by the use of highly induc-
tive source impedances. The input circuit shown in Figure 2 is a practical solu-
tion that can be used to minimize the effects of inductance in the input traces.
For optimum performance, components should be mounted close to the DC/DC
converter. If the application has a high source impedance, low V
benefi t of increased external input capacitance.
I/O Filtering, Input Ripple Current, and Noise Reduction
All BWR 15-17W DC/DC Converters achieve their rated ripple and noise
specifi cations without the use of external input/output capacitors. In critical
applications, input/output ripple and noise may be further reduced by installing
additional external I/O caps.
T E C H N I C A L
IN
to V
Model
All D12A Models
BWR-5/1500-D24A
BWR-12/725-D24A, BWR-15/575-D24A
All D48A Models
OUT
IN
start-up time is the interval of time where the input voltage
to V
OUT
OUT
start-up, the On/Off Control to V
N O T E S
start-up time assumes the converter has its nominal
www.murata-ps.com
Fuse Value
2.5 Amp
4 Amp
2 Amp
1 Amp
OUT
start-up time is also
IN
models can
External input capacitors (C
elements, minimizing line voltage variations caused by transient IR drops in
conductors from backplane to the DC/DC. Input caps should be selected for
bulk capacitance (at appropriate frequencies), low ESR, and high rms-ripple-
current ratings. The switching nature of DC/DC converters requires that dc
voltage sources have low ac impedance as highly inductive source imped-
ance can affect system stability. In Figure 2, C
dc voltage bus. Your specifi c system confi guration may necessitate additional
considerations.
In critical applications, output ripple/noise (also referred to as periodic and
random deviations or PARD) may be reduced below specifi ed limits using fi lter-
ing techniques, the simplest of which is the installation of additional external
output capacitors. These output caps function as true fi lter elements and
should be selected for bulk capacitance, low ESR and appropriate frequency
response. All external capacitors should have appropriate voltage ratings and
be located as close to the converter as possible. Temperature variations for all
relevant parameters should also be taken carefully into consideration. The most
effective combination of external I/O capacitors will be a function of line voltage
and source impedance, as well as particular load and layout conditions.
Floating Outputs
Since these are isolated DC/DC converters, their outputs are "fl oating," with
respect to the input. As such, it is possible to use +Output, –Output or Output
Return as the system ground thereby allowing the fl exibility to generate a
variety of output voltage combinations.
Regulation for BWR 15-17W bipolar converters is monitored between
–Output and +Output (as opposed to Output to Return).
Minimum Loading Requirements
BWR 15-17W converters employ a classical diode-rectifi cation design topology
and require a minimum 10% loading to achieve their listed regulation specifi ca-
tions and a stable operating condition.
Load Regulation
Regulation for the BWR 15-17W bipolar converters is monitored between
–Output and +Output (as opposed to Output to Return). As such regulation will
assure that voltage between –Output and +Output pins remains within the V
accuracy listed in the Performance/Functional Specifi cations table.
V
OSCILLOSCOPE
IN
15-17W, Dual Output DC/DC Converters
–
+
C
C
L
TO
BUS
IN
BUS
= 33μF, ESR < 700m
= 12μH
= 220μF, ESR < 100m
Figure 2. Measuring Input Ripple Current
Technical enquiries email: sales@murata-ps.com, tel:
C
BUS
IN
L
BUS
in Figure 2) serve primarily as energy-storage
@ 100kHz
CURRENT
@ 100kHz
PROBE
C
IN
BUS
MDC_BWR15-17W.B07 Page 4 of 9
BWR Series
and L
+INPUT
–INPUT
BUS
simulate a typical
+1 508 339 3000
OUT